Removing an i/o board or blank panel, Installing an i/o board or blank panel, Align with plastic guides – Extron Electronics FOX Matrix 14400 User Guide User Manual
Page 83: Knurled knobs figure 48. i/o board replacement, Fan assimbl y fan assimbl y
Removing an I/O Board or Blank Panel
Remove an I/O board or blank panel as follows:
1.
For an I/O board, disconnect any connected cables.
2.
Rotate the left and right knurled knobs to completely loosen the screws.
3.
Gently pull on the screws to loosen the board or panel from the backplane.
4.
Slide the board or panel out of the chassis (see figure 48) and place it on an anti-static
surface or in an anti-static container.
ANAHEIM, CA
RESET
RS232/RS422
REMOTE
LAN
ACT
LINK
100-240V
50/60Hz
1.2A MAX.
100-240V
50/60Hz
1.2A MAX.
REDUNDANT
PRIMAR
Y
PRIMAR
Y POWER SUPPL
Y
DISCONNECT BOTH POWE
R
CO
RD
S B
EF
OR
E S
ER
VIC
ING
REDUNDANT POWER SUPPL
Y
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
OU
T
IN
OU
T
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OUT
IN
1 - 16
17 - 32
33 - 48
49 - 64
65 - 80
81 - 96
97 - 112
113 - 128
129 - 144
FAN ASSIMBL
Y
FAN ASSIMBL
Y
Align with
Plastic Guides
IN
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
OU
T
IN
OUT
IN
OUT
IN
OUT
IN
OU
T
IN
OUT
IN
OU
T
IN
OU
T
IN
OU
T
IN
Knurled
Knobs
Figure 48.
I/O Board Replacement
Installing an I/O Board or Blank Panel
Install an I/O board or blank panel as follows:
1.
For an I/O board, orient the board to be installed so that transceiver module A
(
fiber board) or input BNC A (SDI/HD-SDI board) is on the left and transceiver module
or output BNC P is on the right.
2.
For an I/O board, align the board with the left and right chassis guides (see figure 48).
3.
Gently slide the board or blank panel into the enclosure.
For an I/O board, slide the
board toward the front panel until it meets resistance.
4.
Gently seat the board or panel in the backplane.
5.
Use a screwdriver to tighten the left and right screws to secure the board or panel in
place.
FOX Matrix 320x and FOX Matrix 14400 • Maintenance and Modifications
77