Climax PL3000 LATHE - Manual (Page 2)

accessories
Climax Portable Machining & Welding Systems Web site: climaxportable.com
Worldwide Phone:
1.503.538.2185 N. America Toll-Free: 1.800.333.8311 Fax: 1.503.538.7600 E-mail: [email protected]
page 2
No. Description
10649 PL3000 portable lathe, pneumatic
10649CE CE-Compliant model
Complete lathe machine. Turns shafts and roll journals
8.0 - 11.0 inches (203.2 to 279.4 mm) in diameter.
Machine mounts to the end of the shaft with a blank
tapered mounting flange (included). Also includes
counterbalanced mainbody, pneumatic planetary housing,
1.22 hp (.91 kW) air motor, pneumatic conditioning unit,
16.0 inch (406.4 mm) reach turning bar, abrasive belt
holder, tool kit with 3/8 inch (or 10 mm) square HSS lathe
tool and dial indicator, instruction manual, and wooden
storage crate.
Model PL3000 portable lathe, electric
As above with electric motor and speed control instead of
the air motor and pneumatic conditioning unit.
13872
PL3000 Portable lathe, 120V motor
15524 PL3000 Portable lathe, 230V motor
Tapered mounting flange assembly
Precision machined mounting flange securely mounts the
portable lathe to the end of the shaft. One blank mounting
flange is included with the machine.
10640
Blank tapered mounting flange assembly.
Machine to your mounting configuration.
10642 Machine tapered mounting flange
assembly. Factory machined to your
mounting specifications.
10636 Turning bar extension - 22 inch
(558.8 mm) reach
Mount the turning bar extension between the end of the
standard turning bar and the tool housing to extend the
reach of the bar from 16.0 - 22.0 inches (406.4 - 558.8
mm). For longer bar reaches, contact your Climax
representative.
37811 Tooling Pack (not shown)
One HSS 3/8 inch x 3.0 inch side cutting tool
bit, and one HSS
3/8 inch x 3.0 inch top cutting tool bit
in storage case.
Tool holders
Extra tool holders for use with the standard 16.0 inch
(406.4 mm) turning bar and the 22.0 inch (558.8 mm)
turning bar extension. Holders use 3/8 inch or 10 mm
square HSS lathe tool bits.
10643
Tool holder, 4 - 6 inches Used to turn
shafts 4 - 6 inches (101.6 to 152.4 mm)
in diameter
10644 Tool holder, 6 - 8 inches Used to turn s
hafts 6 - 8 inches (152.4 to 203.2 mm)
in diameter.
18368 Tool holder, 8 - 11 inches Used to turn
shafts 8 - 11 inches (203.2 to 279.4 mm)
in diameter
No. Description
10586 Abrasive belt holder
Belt holder mounts to the tool end of the turning bar. Use
with an abrasive belt to produce a fine finish on the shaft.
Abrasive belts not provided.
11784 ID Mounting collet assembly
Allows the PL3000 to be mounted inside work piece
diameters from 4.7 - 10.95 inches (119.4 -278.1 mm).
Assembly includes ID mounting flange, collet body with
fingers and jaws, screw shaft with threaded cones, and
necessary hardware.
28545
ID mounting collet assembly, no jaws
Same as above without fingers or jaws.
ID jaw sets
Jaw set Fits in dia.
28539 0.5 (12.7) 4.7 - 5.95
(119.4 - 151.1)
28540 1.0 (25.4) 5.7 - 6.95
(144.8 - 176.5)
28541 1.5 (38.1) 6.7 - 7.95
(170.2 - 201.9)
28542 2.0 (50.8) 7.7 - 8.95
(195.6 - 227.3)
28543 2.5 (63.5) 8.7 - 9.95
(221.0 - 252.7)
28544 3.0 (76.2) 9.7 - 10.95
(246.4 - 278.1)
NOTE: Drawings are for reference only, are not to scale, and
may not represent actual product.