intimus 20 CC3 - Manual (Page 4)

FEEDING THE PAPER:
- Turn machine on with rocker switch (1) (fig. 2)
(position „I“).
Control display (4) lights up.
- Feed paper through the inlet guide to the cutting
mechanism.
- Machine switches automatically to forward and
draws paper in.
Control display (5) lights up.
The machine switches off automatically after
shredding.
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL
DATA section!
Should the machine become overloaded,
follow the instructions under “MATERIAL
JAM IN THE MACHINE” under “MAL-
FUNCTIONS”.
5 = Control display „forwards run“ (fig. 1)
Lights up if the cutting mechanism starts
running forward after being activated by the
light barrier.
6 = Control display “material jam“ (fig. 1)
Lights when too much material is fed to the
cutters. The cutting mechanism blocks and
stops. The motor is switched off.
7 = Control display “motor overload” (fig. 1)
Lights up if the motor is overloaded. The
machine cannot be started again until the
motor has cooled down.
The shredder may not be used as a step
ladder or as a seat. Danger of falling
due to breakage!
IMPORTANT SAFETY NOTES
EXPLANATION OF THE CONTROLS:
1 = Rocker switch “On / Off” (fig. 2)
The machine is switched on and off with this
switch.
2 = Light barrier (forward running) (fig. 3)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot. Control display lights up.
3 = Backwards button (fig. 1)
When this button is pressed briefly, the cutting
mechanism runs backwards.
Note: The cutting mechanism only runs
backwards as long as the button is held
(touch function).
4 = Control display „ready“ (fig. 1)
Lights when the rocker switch (1) is operated
(position „I“).
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all
loose articles of clothing, ties,
jewelery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
SCOPE OF APPLICATION:
The intimus 20SC2 / 20CC3 data shredder is
designed for shredding general printed material
and credit cards.
This machine should only be used for
shredding paper (incl. single staples
and paper clips) and credit cards!
Any attempt to shred other types of data
medium may result in damage to the
machine (e.g. destruction of the cutting
mechanism etc.).
INSTALLATION:
- Unpack and set machine upright.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
20SC2 20CC3
fig. 2 fig. 3
1
2
fig. 1
5
7
3
4
6
89823 5 03/13
4
OPERATION
INITIATION
GB Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung