FIg. 4, Maintenance, Technical data malfunctions – intimus 402 Wide Body User Manual
Page 5: Accessories
MAINTENANCE
5
CLEANING THE PHOTOCELLS (fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is pos-
sible that the machine will not turn off, due to the
broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
MAINTENANCE CUTTING BLOCK:
(1.9x15 mm, 3.8x30 mm,
0.8x12 mm and 0.8x4.5 mm)
After approximately 15 minutes of con-
tinuous use, run the cutting system in
reverse for 15 to 20 seconds and spray
some of the enclosed Special Oil onto the
cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (3) (fig. 1).
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
TECHNICAL DATA
MALFUNCTIONS
PAPER JAM:
If too much paper is fed to the cutting system the
machine will react as follows:
- The cutting system blocks, reverses a bit to
release the paper and then stops.
- The motor shuts down automatically.
- The pilot lamp (6) (fig. 1) lights up.
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(3) (fig. 1).
- The pilot lamp (6) (fig. 1) goes off.
- Remove excess paper from the machine and
continue shredding with less paper.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
the pushbutton switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the
plug connected to the mains?
Mains connection: 2-pole mains switch,
internal appliance plug,
separate power cord
- Is the
pushbutton switch (1) on?
- Is the
door closed?
- Is the
receptacle full?
The receptacle has to be emptied.
- Is there a
paper jam?
Follow the instructions under „paper jam“.
- has the
motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
ACCESSORIES
Description
Order-No.
Plastic bag, 300 x 300 x 700 x 0,018 mm
99925
Lubricant, 125 ml bottle (cross-cut)
99943
Note: For orders of special accessories and spare parts, please contact your dealer.
Cutting width:
302/402:
1.9 mm (strips)
3.8 mm (strips)
5.8 mm (strips)
302CC/402CC:
1.9x15 mm (cross-cut)
3.8x30 mm (cross-cut)
302HS/402HS:
0.8x12 mm (cross-cut)
302SF:
0.8x4.5 mm (cross-cut)
Cutting capacity:
302/402:
1.9 mm:
12-14 sheets (70g/m
2
)
3.8 mm:
19-21 sheets (70g/m
2
)
5.8 mm:
25-27 sheets (70g/m
2
)
302CC/402CC:
1.9x15 mm:
10-11 sheets (70g/m
2
)
3.8x30 mm:
15-17 sheets (70g/m
2
)
302HS/402HS:
5-6 sheets (70g/m
2
)
302SF:
3-4 sheets (70g/m
2
)
Supply voltage:
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/240V/50Hz:
10 amps (slow-blow)
120V/100V/50/60Hz:
20 amps (slow-blow)
Working width:
240 mm
Noise level:
approx. 54 dB(A)
Power:
0.55 kW
Dimensions (WxDxH):
302/-CC/-HS/-SF:
385x280x635 mm
402/-CC/-HS:
385x280x740 mm
Weight:
302/-CC/-HS/-SF:
approx. 18.5-20 kg
402/-CC/-HS:
approx. 19.5-21 kg
GB
fig. 4
2
302 302CC 302HS 302SF 402 402CC 402HS