intimus POWER 16.86 - Manual (Page 17)

The machine may not be modified in
any way. Operation of the machine
is prohibited if modifications are un-
dertaken.
ENERGY SAVING TIP:
Make sure that the machine is switched off
overnight (turn mains switch (1) (fig. 6) to ”0”
position).
CHECKING THE OIL LEVEL (fig. 19):
Unscrew the dipstick (43) in order to check the oil
level. The marking on the dipstick must be wetted
with oil. If this is not the case, add oil.
CUTTING SYSTEM MAINTENANCE:
After approximately 8 hours of continu-
ous operation, open the cover flap (27)
and spray a modest amount of the in-
cluded special oil onto the cutting system
at the shredder.
GEARBOX MAINTENANCE:
The synchron-gears, as well as the chain wheels
and drive chains must be lubricated once per
month.
The mains switch (1) (fig. 6) must be
turned off and the mains plug must
be removed from the electrical outlet
before opening the machine.
Proceed as follows:
1. Remove the right-hand side panel from the
housing.
2. Use a brush or a grease gun to lubricate the
above mentioned parts with a commercially
available grease.
3. Replace the side panel and insert the mains
plug into the electrical outlet. The machine can
be placed back into service.
MOTOR MALFUNCTIONS:
If the shredder or baler should become overloaded, an
installed thermostat breaks the electrical circuit for full
operation. The „malfunction - motor“ indicator light (8)
flashes.
While the overheated motor of shredder or baler is cooling
down, both may still be operated by inching (shredder with
reduced power - star connection), for example to return
material to be cut.
The shredder may be operated with reduced
power only to remove material, or for final
shredding of material which has already been
introduced. Other operation in this mode can
lead to destruction of the motor.
After cooling (approx. 5-10 minutes) the light goes off and
the unit can once again be operated at full power (delta
connection).
Note: If, after the motor has cooled, the unit cannot be
operated at full power (light (8) remains on), there is a
defect in the machine. In this case our customer service
must be contacted.
If repairs are required, the mains plug must
be removed from the electrical outlet before
the machine is opened, and the mains switch
must be turned off and locked into the off
position with a pad lock.
MALFUNCTIONS CHECKLIST:
If the system does not function, check the following
points:
- is the mains plug from the shredder connected to the
mains outlet?
- is the connector plug from the baler plugged into the
outlet (18) at the shredder?
- has the safety switch activator (19) been inserted into
the safety switch at the baler?
- has the key switch (2) been activated?
- is the mains switch (1) turned on?
- is the emergency stop bar (14) in the forward posi-
tion?
Pull red bar at table forward.
- is there a paper jam in the machine?
Follow the instructions for “AUTOMATIC RESPONSE
IN CASE OF OVERLOADING”
- are the inlet flap (30) and the discharge flap (31) at
the baler closed?
- is the cover flap (27) closed?
See description under ”OUTLET JAM”.
- is one of the motors overloaded?
See description under ”MOTOR MALFUNCTIONS”.
- has one of the electrical phases failed?
Check the three line fuses at the mains outlet and
replace if necessary.
If you still cannot isolate the fault or other
faults are statable, the machine shouldn’t
be operated. Please report to / notify our
customer service department.
43
15.85/16.86
84237 12 01/13
17
GB
MALFUNCTIONS
MAINTENANCE
TECHNICAL DATA
ACCESSORIES
DISPOSING
Description Best.-Nr.
Plastic sac, 600 x 490 x 1500 x 0,06 mm 99969
Bottle of oil, 110 ml 88035
Strap roll, 9 mm / 500 m 80661
Note: Please contact your dealer when ordering accessories and replacement parts.
SHREDDER:
Cutting Width: 11.8 x 55 mm
7.8 x 55 mm
3.8 x 55 mm
Cutting capacity:
15.85:
11.8 x 55 mm: 260-320 sheets (70 g/m 2 )
7.8 x 55 mm: 200-260 sheets (70 g/m 2 )
6 x 50 mm: 180-210 sheets (70 g/m 2 )
16.86:
11.8 x 55 mm: 400-550 sheets (70 g/m 2 )
7.8 x 55 mm: 350-420 sheets (70 g/m 2 )
6 x 50 mm: 300-330 sheets (70 g/m 2 )
Working Width: 500 mm
Power:
15.85: 5.5 kW
16.86: 7.5 kW
Weight:
15.85: approx. 696 kg
16.86: approx. 726 kg
BALER:
Press Force: approx. 8 t
Power: 4 kW
Chamber Space: 570x460x1000 mm
Inlet opening: 570x340 mm
Machine Weight: approx. 530 kg
Bale Weight: approx. 60-80 kg
Bale Size: 500x600x750 mm
COMBINATION:
Supply voltage: 400 V/ 50 Hz
230 V/ 50/60 Hz
415 V/ 50 Hz
220 V/ 60 Hz
200 V/ 50 Hz
200 V/ 60 Hz
Pre-Fusing:
(gl fuse, type 1 assignment)
400 – 415V/50Hz: 35 A
220 – 230V/50HZ: 40 A
200V/50 – 60Hz: 63 A
Length: 2810 mm
Width: 1200 mm
Height: 1550 mm
Length with Open
Discharge Flap: 3480 mm
Noise Level: > 74 dBA
Overall Weight:
15.85: approx. 1226 kg
16.86: approx. 1256 kg
(shredder and baler)
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
fig. 19
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung