Finish Thompson UC (S/N 125040 and lower) - Manual (Page 6)

6
Unpacking and Inspection
Unpack the pump and examine for any signs of shipping damage.
If damage is detected, save the packaging and notify the carrier immediately.
To install the pump, follow the installation instructions provided.
WARNING: The pump and associated components are heavy. Failure to properly
support the pump during lifting and movement could result in serious injury or damage to
the pump and components. (See figure A)
Model Number and Serial Number
Record the model number and serial number for future reference. Use the location
provided on the front cover of this manual. This is important information when ordering replacement parts or when technical as-
sistance is required. The model and serial number are found on a label located on the motor adapter.
Installation
To install a motor to a pump end, see section Assembly of Pumps without Motors, and then proceed to section Foundation.
Note: A hydrostatic test was performed prior to shipment. It is normal for a small amount of water to be retained inside the pump.
Pumps with Motors:
Proceed to Foundation Section.
UC1516 =
637 (6 3/8”); 625 (6 1/4”); 612 (6 1/8”); 600 (6”); 587 (5 7/8”); 575 (5 3/4”); 562 (5 5/8”); 550 (5 1/2”); 537 (5 3/8”);
525 (5 1/4”); 512 (5 1/8”); 500 (5”); 487 (4 7/8”); 475 (4 3/4”); 462 (4 5/8”); 450 (4 1/2”); 437 (4 3/8”); 425 (4 1/4”);
412 (4 1/8”); 400 (4”)
UC1518 =
812 (8 1/8”); 800 (8”); 787 (7 7/8”); 775 (7 3/4”); 762 (7 5/8”); 750 (7 1/2”); 737 (7 3/8”); 725 (7 1/4”); 712 (7 1/8”);
700 (7”); 687 (6 7/8”); 675 (6 3/4”); 662 (6 5/8”); 650 (6 1/2”); 637 (6 3/8”); 625 (6 1/4”); 612 (6 1/8”); 600 (6”)
UC326 =
637 (6 3/8”); 625 (6 1/4”); 612 (6 1/8”); 600 (6”); 587 (5 7/8”); 575 (5 3/4”); 562 (5 5/8”); 550 (5 1/2”); 537 (5 3/8”);
525 (5 1/4”); 512 (5 1/8”); 500 (5”); 487 (4 7/8”); 475 (4 3/4”); 462 (4 5/8”); 450 (4 1/2”); 437 (4 3/8”); 425 (4 1/4”)
Motor frame: 14 = 145TC (available with “A” magnet set only)
18 = 184TC (available with “A” or “B” magnet set)
21 = 215TC (available with “A” or “B” magnet set only)
25 = 256TC (available with “B” magnet set only)
90 = 90 frame with B14 flange (available with “A” magnet set only)
10 = 100/112 frame with B14 flange (available with “A” magnet set only)
13 = 132 frame with B5 flange (available with “A” or “B” magnet set only)
16 = 160 frame with B5 flange (available with “B” magnet set only)
FO = Frame mounted, flood oil
FB = Frame mounted, regreasable bearings
Bump Ring: B = Non-sparking Bronze
If the bronze bump ring is required for explosion proof environments, add the letter “B” after the two digit
motor frame code (14B for example).
Note: Close coupled and frame mounted pumps with the bronze bump ring option “B” will be ATEX certified.
All Atex certified pumps must utilize the bronze bump ring.
UC Impeller Diameters: