Watlow EZ-ZONE RMC - Manual (Page 179)

Watlow EZ-ZONE ® RMC Module • 176 • Chapter 7 Features
Control Function
Control
Overview
Instances - 1 to 4 per RMC
Control Mode
Remote Set P
oint Enable
Remote Set P
oint Enable
Remote Set P
oint
Type
User F
ailure
Action
Loop Error Clear Request
Input Error F
ailure
Fixed P
ower
Open Loop Detect Enable
Open Loop Detect
Time
Open Loop Detect Deviation
Ramp
Action
Ramp Scale Ramp Rate
Profiling Enable
Closed Loop Low Set P
oint
Set P
oint
Open
Limit
Low
Closed Loop High Set P
oint
Set P
oint
Open
Limit
High
Heat
Algorithm
Cool
Algorithm
TRU-TUNE+ Enable
Autotune
Aggressiveness
Peltier Dela
y
TRU-TUNE+ Band TRU-TUNE+ Gain Cool Output Curve Autotune Set P
oint
Autotune
Closed Loop Set P
oint
Idle Set P
oint
Heat Proportional Band Cool Proportional Band
Heat Hysteresis Cool Hysteresis
Deadband
Open Loop Set P
oint
Cool Power
Heat Power
Tune Status
Loop Error
Closed Loop Set Point
Open Loop Set Point
Loop Power
Process Value Active
Source Function A
Source Instance A
Source Zone A
Source Error A
Source Function B
Source Instance B
Source Zone B
Source Error B
Time Integral
Time Derivative
[SFn;A] Source Function A : Analog Input, Process Value
`[h;Ag] Heat Algorithm : Off, PID, On/Off
[`C;Ag] Cool Algorithm : Off, PID, On/Off
[t;tUn] TRU-TUNE+ Enable : No, Yes
[t;bnd] TRU-TUNE+ Band : 0 to 100
[`t;gn] TRU-TUNE+ Gain : 1 to 6
[t;Agr] Autotune Aggressiveness : Under, Critical, Over
[`r;En] Remote Set Point Enable : No, Yes
[`Si;b] Source Instance B (Remote Set Point Source Instance) : 1 to 250
[`S2;b] Source Zone B : 0 to 16
[MAn] Fixed Power : -100.0 to 100.0 %
[`L;dE] Open Loop Detect Enable : No, Yes
[`L;dt] Open Loop Detect Time : 0 to 3,600 seconds
[``rP] Ramp Action : Off, Startup, Set Point, Both
[`r;SC] Ramp Scale : Hours, Minutes
[`r;En] Remote Set Point Enable : No, Yes
[`C;M] Control Mode : Off, Auto, Manual
[A;tSP] Autotune Set Point : 50 to 200 %
[`AUt] Autotune : No, Yes
[`C;SP] Closed Loop Set Point : -1,999.000 to 9,999.000
[`id;S] Idle Set Point : -1,999.000 to 9,999.000
[`h;Pb] Heat Proportional Band : 0.001 to 9,999.000
[`h;hy] Heat Hysteresis : 0.001 to 9,999.000
[`C;Pb] Cool Proportional Band : 0.001 to 9,999.000
[`C;hy] Cool Hysteresis : 0.001 to 9,999.000
[``ti] Time Integral : 0 to 9,999 seconds
[``td] Time Derivative : 0 to 9,999 seconds
`[C;Cr] Cool Output Curve : Off, Non-linear curve 1, Non-linear curve 2
[`r;ty] Remote Set Point Type : Auto, Manual
[`L;SP] Low Set Point : -1,999.000 to 9,999.000
[`h;SP] High Set Point : -1,999.000 to 9,999.000
[SP;Lo] Set Point Open Limit Low : -100.0 to 100.0 %
[SP;hi] Set Point Open Limit High : -100.0 to 100.0 %
[`L;dd] Open Loop Detect Deviation : -1,999.000 to 9,999.000
[`r;rt] Ramp Rate : 0.000 to 9,999.000
[Pro;E] Profiling Enable: No, Yes
[``db] Deadband : -1,000.000 to 1,000.000
[`o;SP] Open Loop Set Point : -100.0 to 100.0 %
[`iS;A] Source Instance A : (not changeable)*
[LooP] Loop Menu
[`SEt] Setup Page
[LooP] Loop Menu
[oPEr] Operation Page
[`P;dL] Peltier Delay : 0.0 to 5.0
Note: Control Loop primary source instance must match
Process Value or Analog Input instance.
Loop Power : -100.0 to 100.0 %
Loop Error: None, Open Loop, Reversed Sensor
Loop Error Clear Request : Ignore, Clear
Tune Status : Off, Cross 1 Positive, Cross 1 Negative,
Cross 2 Positive, Cross 2 Negative, Cross 3 Positive,
Cross 3 Negative, Measuring Max, Measuring Min,
Calculating, Complete, Timeout
[C;MA] Control Mode Active : Off, Auto, Manual
[`h;Pr] Heat Power : 0.0 to 100.0 %
[`C;Pr] Cool Power : 0.0 to 100.0 %
[`C;SP] Closed Loop Set Point : -1,999.000 to 9,999.000
[`Pu;A] Process Value Active : -1,999.000 to 9,999.000
[Mon] Monitor Menu
[oPEr] Operation Page
Control Mode Active
[SFn;b] Source Function B : (Remote Set Point Source) : None, Analog
Input, Current, Cool Power, Heat Power, Power, Linearization,
Math, Process Value, Set Point Closed, Set Point Open, Variable
[fail] Input Error Failure : Off, Bumpless Transfer, Manual Power,
User
[`Ufa] User Failure Action : Off, Bumpless Transfer, Manual Power,
User