NSi Industries DGUM100 - Manual (Page 7)

REVIEW/MODIFY/ADD/DELETE
REVIEW: Reviewing is done in the set mode. Press
mode key until first setting appears. Pressing the
ENTER button will advance the counter (which
appears in the two digits on the right) and shows you
the next schedule event entered. Events are num-
bered based on the order with which they were
entered, and not on when they will be executed, so the
first event you set will be #01, the second #02, etc...
MODIFY: During the review process, the DAY, HOUR,
MIN, and ON/OFF keys can all be used to modify the
settings. You can use the first three keys to modify
when the event will take place, and the ON/OFF key to
change an ON event to an OFF event, or visa-versa.
ONCE YOU HAVE MADE THE NECESSARY
CHANGE, YOU MUST PRESS THE ENTER KEY (for
each change) TO STORE THEM.
ADD: You may add events at any time by pressing the
mode key until the unit is in the set mode. Then press
ENTER key to advance to the next open set point.
Enter new schedule as indicated in section “To Set
Schedule”.
DELETE: If you choose to delete a schedule, simply
modify the HOURS and MINUTES, until the time
display reads --:--. This will occur after scrolling past
11 P.M. with the HOUR key and “59” with the MIN
key. Then press ENTER to delete the event.
OVERRIDE
In order to temporarily change the current ON or OFF
status of a load, simply press the override key. This
can only be done when the unit is in the RUN mode.
The load status will flash indicating that this is a
change from a scheduled event.
In order to cancel the override, press override
key again.
MLI-158(A)
TORK ®
1 GROVE STREET, MOUNT VERNON, NEW YORK 10550
TEL: 914-664-3542 • FAX: 914-664-5052 • http:// www.tork.com
1. Press DAY/MONTH key to set day(s).
NOTE: The following is a listing of the sets of days
which can be set:
MO to FR (MO, TU, WE, TH, FR)
SA and SU (SA, SU only)
MO to SA (MO, TU, WE, TH, FR, SA)
SU to SA (SU, MO, TU, WE, TH, FF, SA)
Individual days: SU, MO, TU, WE, TH, FR, SA, and D
for Special Day (usually a holiday).
A special holiday schedule can be entered if you want
to be able to repeat this particular schedule on holi-
days only.
2. Press HOUR key to set hour {check AM/PM}.
3. Press MiN key to set minutes.
4. Once desired days are set, press ON/OFF key to
set ON or OFF event. If all of the information you
entered is correct, press ENTER key to store the
event.
Display will now show --:-- 02. This tells you that the
first event has been entered, and that the unit is ready
to accept the second entry. Repeat above steps 1 to 4
to set more schedule events (keep in mind, an “ON” is
one event and an “OFF” is another).
Note: When the unit is returned to the run mode,
check the load status of the current setting. If it is
showing OFF but should be ON, press the override
key since the unit does not “look back” to the set-
ting just entered. However, the unit will correct
itself at the next scheduled event and no further
alteration will be necessary.
SPECIAL DAY (HOLIDAY)
To execute this schedule at any time, simply press the
SP DAY key while the unit is in the RUN mode. A let-
ter “D” will appear in the upper right corner and the
Special Day schedule (previously set) will repeat for
as many days as you want. If no schedule was
entered, the last event (ON or OFF) will remain active.
To return to normal 7 day program operation, press
the SP DAY key again and the letter “D” will disappear,
indicating regular program operation.
7