Canon EOS C300 PL - Manual (Page 172)

Troubleshooting
172
Troubleshooting
If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center
if the problem persists.
Power source
The camcorder will not turn on or it turns off by itself.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Shortly after turning it on, the camcorder turns off on its own.
- You are using a DC coupler or a battery pack that is not compatible for use with this camcorder. Use a recommended
battery pack (A 184).
Cannot charge the battery pack.
- The temperature of the battery pack is outside the charging range. If the battery pack’s temperature is below 0 °C,
warm it before charging it; if it is above 40 °C, let the battery pack cool down before charging it.
- Charge the battery pack in temperatures between 0 °C and 40 °C.
- The battery pack is faulty. Replace the battery pack.
The battery pack is exhausted extremely quickly even at normal temperatures.
- Check the [Battery/Hour Meter] status screen (A 169) to see whether the battery pack is at the end of its service life.
If so, buy a new battery pack.
Recording
The camcorder’s controls are not responsive/disabled
- The grip unit’s plug may not be correctly connected to the camcorder. When attaching the grip unit to the camcorder,
make sure the grip unit’s plug is firmly inserted all the way into the connection terminal on the camcorder (A 41). If
you changed the angle of the grip unit, make sure you did not partially disconnect the plug by mistake.
- When the Q switch is set to C, all buttons except for the START/STOP button are locked and cannot be
operated. (Depending on the [Other Functions] > [Custom Function] > [C START/STOP] setting, the START/STOP
may be locked as well.) Set the Q switch to CAMERA.
Pressing the START/STOP button will not start recording.
- The CF card is full or it already contains the maximum number of clips (999 clips). Delete some clips (A 134) or save
your clips (A 143) and initialize the CF card (A 45) to free some space. Alternatively, replace the CF card.
- The camcorder is in lens exchange mode. Press the assignable button set to [LENS EXCHANGE] to exit this mode.
The point where the START/STOP button was pressed does not match the beginning/end of the recording.
- There is a slight interval between pressing the START/STOP button and the actual start/end of recording. This is not a
malfunction.
The camcorder will not focus.
- The viewfinder is not adjusted. Use the dioptric adjustment dial to make the proper adjustment (A 38).
- The lens is dirty. Clean the lens with a soft lens-cleaning cloth.
When a subject flits across in front of the lens, the image appears slightly bent.
- This is a phenomenon typical of CMOS image sensors. When a subject crosses very quickly in front of the camcorder,
the image may seem slightly warped. This is not a malfunction.
Bright red, green or blue dots appear on the screen.
- The camcorder’s CMOS sensor is a delicate piece of precision engineering. Direct exposure of the sensor to ion rays or other
types of cosmic radiation may affect it and this may rarely appear as bright colored dots on the screen. This is the nature of
CMOS image sensors and does not represent a malfunction. Adjusting the black balance (A 48) may help solve the problem.
- The effects of the damage may be more noticeable when the camcorder is used in places subject to high
temperatures, when a high ISO speed or gain level is used and when slow shutter speeds are used.
Changing between recording (ÜREC) and record pause (STBY) takes longer than usual.
- When the CF card contains a large number of clips, some operations may take longer than usual. Save your clips
(A 143) and initialize the CF card (A 45). Alternatively, replace the CF card.
The camcorder cannot record to a CF card properly.
- This may occur as recordings are made and deleted over time. Save your clips (A 143) and initialize the CF card (A 45).
COP
Y