Működési leírás, Measurement – Nikon Laser User Manual

Page 152

Advertising
background image

Ru

Se

Nl

Dk

Pl

Hu

Cz

Fi

No

En

De

Fr

Es

It

Ro

302

Ru

Se

Nl

Dk

Pl

Hu

Cz

Fi

No

En

De

Fr

Es

It

Ro

303

Működési leírás

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

3. A folyamatos mérés elindításához tartsa lenyomva a

gombot

kb. 5 másodpercig. A belső kijelzőn a "Távolság" és "Hibás mérés"

kijelzések váltakoznak.

Megjegyzés: A mérés ideje alatt a lézersugárzás jele villog.

Megjegyzés: Ha nem nyomja tovább a gombot, a folyamatos mérés

leáll.

【Folyamatos mérés】

Hibás a mérés

vagy nem lehet

távolságot mérni.

Megjelenik a mért

alak.

(1. céltárgy)

Megjelenik a mért

alak.

(2. céltárgy)

5. Példák bemutatása minden egyes üzemmódra

Aktuális távolság és

magasság üzemmód

Vízszintes távolság és

magasság üzemmód

Golf üzemmód

Aktuális távolság üzemmód

Méter

[

]

Yard

[

]

1.

Nézze meg, hogy az LCD panel be van-e kapcsolva.

2.

Nyomja le és tartsa lenyomva a

gombot körülbelül két

másodpercig.

3.

Amikor a kijelzett mértékegységet átkapcsolta, engedje el a

gombot.

4.

A mértékegység beállítása után a gép átalakítja az

eredményeket, és az Ön által kiválasztott módon jeleníti meg.

6. Váltás a mérés/kijelző üzemmódok között

(A gyári alapbeállítás a Tényleges távolság és magasság üzemmód)

1. Nézze meg, hogy az LCD panel be van-e kapcsolva.
2. Nyomja meg a

gombot 0,5 másodpercen belül.

3. Engedje fel a

g

ombot az üzemmódra kapcsoláshoz.

4. Ismételje a 2. és 3. lépéseket a kívánt üzemmód megjelenéséig.
5. Az üzemmódra akkor kapcsoljon át, miután a gép átalakította az eredményeket az új üzemmódhoz.
6. Miután beállította az üzemmódot, a gép a mérést az új üzemmódban végzi el.

Tényleges távolság és magasság

üzemmód

Vízszintes távolság és magasság

üzemmód

Tényleges távolság üzemmód

Golf üzemmód

Amikor például egy golfpályán a kitűzőzászló nyelét méri, a könnyű

mérés érdekében használja az Első céltárgy elsőbbsége és a

Folyamatos mérés üzemmódot. Amennyiben Ön és a kitűzőzászló nyél

között nincs akadály, a legkisebb szám mutatja a célba vett zászlónyél

távolságát.

A MODE gombot megnyomva az üzemmódok a fentiekben megadott sorrend szerint változnak.

5. A kijelzett mértékegység kiválasztása (A gyári alapbeállítás a

yard.)

4. Mérés után a "Távolság" vagy a "Hibás mérés" jelzések jelennek meg

8 másodpercig, aztán a gép kikapcsol. Ha megnyomja a

gombot a bekapcsolás közben (míg a belső kijelző világít), egy új

egyszeri mérés indul el.

Üzemmód nevek

Tényleges távolság és

magasság üzemmód

Vízszintes távolság és

magasság üzemmód

Golf üzemmód

Tényleges távolság

üzemmód

Felfelé néző (+) szög,

Emelkedő

Nincs jelzés

Lefelé néző (-) szög,

Lejtő

Felső, 7-szegmenses

kijelző

Tényleges távolság

Vízszintes távolság

Lejtéshez igazított

távolság

Tényleges távolság

Alsó, 7-szegmenses

kijelző

Magasság

Magasság

Tényleges távolság

Nincs kijelzés

Jel

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

A mérések kivitelezése közben villog.

Measurement

1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and
“fail to measure” indicator alternately.
Note: Laser irradiaton mark is blinking during the measurement.
Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target

.

Position the target at the center of the reticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement.

Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER
button during power-on (while the internal display is lit), another measrement starts.

Advertising