Vaddio ProductionVIEW HD-SDI - Manual (Page 20)

ProductionVIEW HD-SDI
Control Pin-out Table for ProductionVIEW HD-SDI
Camera Control Ports 1 through 6 - RS-232 on RJ-45 Connectors:
PIN# Signal
1) Unused
2) Unused
3) Unused
4) Unused
5) Unused
6) GND
7) TXD (to RXD of camera)
8) RXD (from TXD of camera)
API and Programming Language
+--------------------------------------------------------------------------+
| Vaddio ProductionVIEW HD-SDI |
+--------------------------------------------------------------------------+
| ? - This Menu |
+------------------------ System Access -----------------------------------+
|Power x- Power(On/Off) |SysMode x- (Manual/Auto) |
|ProgIn x- Program (1-6,7-LSG,8-PIP)|Mix - Mix/FTB Button |
|PrevIn x- Preview (1-6,7-LSG,8-PIP)|Cut - Cut Button |
|Camera x- Switch to Camera(1-6) |Take - Take Button |
|Preset x- Go to Preset(1-12) |Wipe - Wipe Button |
|Store x- Store Preset(1-12) |lsgSize x- Lsg Size(0-3) |
|WipeSel x- Effect select:(0-8) |lsgDen x- Lsg Density(0-9) |
|0:Wipe UL>LR,1:Wipe Top>Bot, |BLCx-BacklightComp(On,Off) |
|2:Wipe UR>LL,3:Wipe L>R,4:Wipe Cnt>Out,|AWBx- AutoWhiteBal(On,Off) |
|5:Wipe R>L,6:Wipe LL>UR,7:Wipe Bot>Top,|PipLoc x,x- Location,size(0-2) |
|8:Wipe LR>UL | 0:UL,1:UR,2:LL,3:LR |
+--------------------- Joystick Pan, Tilt, Zoom----------------------------+
|JPanDir x,x-Port(0-6)Invert/Normal |JPanSpd x,x-Port(0-6),Spd(1-24)|
|JTiltDir x,x-Port(0-6)Invert/Normal |JTiltSpd x,x-Port(0-6),Spd(1-20)|
|JZoomDir x,x-Port(0-6)Invert/Normal |JZoomSpd x,x-Port(0-6),Spd(0-7) |
+--------------------- Preset Pan, Tilt, Zoom------------------------------+
|PanSpeed x- Preset Pan Speed (1-24) |TiltSpeed x-Preset Tilt Spd(1-20)|
|ZoomSpeed x- Preset Zoom Spd (0-7) |Home - Home Camera |
|PresetLoc x- Store Preset (InCam/Lcl) |OnCamInit x- (Home/Preset12) |
+--------------- Camera ----------------+----------------------------------+
|Move x- (Up/Down/Stop/Left/Right) |Zoom x- (In/Out/Stop) |
|Iris x,x- (Up/Down/Auto/Manual),Value| |
|Focus x,x- (Up/Down/Auto/Manual),Value| |
+--------------------- System Setup and Utilties---------------------------+
|SetDefault x- Set Default Preset(1-12) |Tally - Idle Tally(High/Low)|
|DefaultCam x- Set Default Camera(1-6) |IdleRtn x- Default Timer(0-60) |
|ExtTrigger x- Combine (AllCam1/Cam1&2) |SerialEcho x- Echo Serial (On/Off)|
|FTB x- Fade U/D/(10-40) |SerialInfo x- Status (On/Off) |
|Reset - 'CPU'Reset |SwMode x- Switch(Single/Dual) |
|DspCams - List connected cameras |Version - Firmware Version |
|ClearAll - Clear all presets |Config - List Config Settings|
|SaveConfig - Manual Config Save |ResetVideo - Re-Load Video config
|Rescan - Rescan Cameras |InitTrig - Init Idle Trig State
+---------------------------------------------------------------------------------------------------------------+
12345678
ProductionVIEW HD-SDI Manual 341-852 Rev. B Page 20 of 22