Vaddio WallVIEW HD-18W - Manual (Page 9)

WallVIEW HD-18
WallVIEW HD-18 Manual 341-888 Rev. D Page 9 of 16
Step 5:
Follow the sample wiring diagram on this page for connecting the Cat-5e cables to the camera and Quick-
Connect Short Range, using a compatible Vaddio ProductionVIEW joystick camera controller. Additional
diagrams are available on our website for installation with a variety of videoconference codecs, utilizing
the RS-232 Input and Output connectors for IR signaling.
Note: Check all Cat-5e cables for continuity in advance of the final connection. Plugging the EZ
POWER/VIDEO Cat-5e cable into the wrong RJ-45 may cause damage to the camera system
and void the warranty.
Step 6:
Connect the Vaddio 24 VDC power supply to an AC outlet. Power will travel down the Power/Video Cat.
5 cable to the camera. The camera will “Home” to a centered position ready for control information from
the IR remote control or RS-232 camera controller of the integrators’ choice. To insure proper continuity
of control and operation of the cameras, the RS-232 controller (control system or joystick) should be
powered on after the camera.
IMPORTANT NOTE:
Strain relief for the 15-pin connector is highly recommended on the DE-15 connector on the back of the
WallVIEW HD-18 system.
WallVIEW HD-18 General Specifications
Part Numbers WallVIEW HD-18 999-6905-000 (North America)
WallVIEW HD-18 999-6905-000W (Arctic White - North America)
WallVIEW HD-18 999-6905-001 (INT’L)
WallVIEW HD-18 999-6905-001W (Arctic White - INT’L)
 Vaddio ClearVIEW HD-18
Image Device 1/3” CCD
Picture Elements 1.3 Megapixels
Signal System HD: 1080p, 1080i or 720p @ 59.94; 1080p @ 60; 1080p, 1080i or 720p @ 50
SD: Composite NTSC or PAL (simultaneous with HD) NOTE: SD output not on Quick-Connect SR
Lens 18x Optical Zoom
Focal Length f=4.7 to 84.6mm
Horizontal Viewing Angle 3.2 to 55.2 degrees (16:9)
Frame Delay 1 frame
Video S/N Ratio >50 dB
Invertible Yes
Minimum Illumination 1.8 lux
Control Protocol VISCA
Serial Communication RS-232 (9600 or 38,400)
Pan Range +170 degrees to -170 degrees
Tilt Range +90 degrees to -30 degrees
Pan/Tilt Speed 0.25° to 60° degrees/second
Preset Positions 16 (internal), 6 recalled via IR Remote
Weight 5.8 lbs. (2.63 kg.)
 Quick-Connect Short Range Interface (SR)
Connectors Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
Power/Video RJ-45: Supplies power to, and component HD from the camera, up to 100 feet
Video Output: DE-15 connector for HD Analog Component (Y,PB,PR) video only – no SD video
IR Output: Transmits modulated or non-modulated IR signals received from the HD-18 IR receiver
Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
Control Out RJ-45: Sends RS-232 from Quick-Connect SR to the camera
Cat. 5 Cable Distance Up to 100’ (30.5m)
Power Supply 24 VDC, 2 Amp
Dimensions 1-RU Rack Mount - 1.75” H x 5.5” W x 6” D (4.45 cm x 14 cm x 15.2 cm)

CONCEAL Wall Mounting System for Vaddio ClearVIEW HD-18
Dimensions 5.125” H x 6.75” W x 10” D (13 cm x 17.15 cm x 25.4 cm)
Weight Approx. 2.4 lbs. (1.1kg)