Kramer Electronics VS-88HC - Manual (Page 43)

Kramer Protocol 2000
39
Table 16: Instruction Codes for Protocol 2000
Note: All values in the table are decimal, unless otherwise stated.
INSTRUCTION DEFINITION FOR SPECIFIC INSTRUCTION
# DESCRIPTION INPUT OUTPUT
NOTE
0 RESET VIDEO 0 0 1
1 SWITCH VIDEO Set equal to video input
which is to be switched
(0 = disconnect)
Set equal to video output which is
to be switched
(0 = to all the outputs)
2, 15
2 SWITCH AUDIO Set equal to audio input
which is to be switched
(0 = disconnect)
Set equal to audio output which
is to be switched
(0 = to all the outputs)
2
3 STORE VIDEO STATUS Set as SETUP # 0 - to store
1 - to delete
2, 3, 15
4 RECALL VIDEO STATUS Set as SETUP # 0 2, 3, 15
5 REQUEST STATUS OF A
VIDEO OUTPUT
Set as SETUP # Equal to output number whose
status is reqd
4, 3
6 REQUEST STATUS OF AN
AUDIO OUTPUT
Set as SETUP # Equal to output number whose
status is reqd
4, 3
7 VIS SOURCE Set as input # when
OUTPUT byte = 6;
OR
set as output # when
OUTPUT byte = 7;
OR
set as blank period
(in steps of 25ms) when
OUTPUT byte = 32;
OR
set = 0. *****
0 - No VIS (immediate)
1 - Input # 1
2 - External digital sync
3 - External analog sync
4 - Dynamic sync
5 - Inter-machine sync
6 - Input # (INPUT byte)
7 - Output #(INPUT byte)
8 - User-defined sync
32 - RGBHV seamless switching
64 - Set for delayed switch
65 - Execute delayed switch
66 - Cancel delayed switch
setting
2, 5, 17, 18
0 0 - audio-follow-video
1 - audio breakaway
2 8 BREAKAWAY SETTING
1 0 - FOLLOW mode
1 - Normal mode
15
0 - for video 0 - CV
1 - YC
2 - YUV
3 - RGBS
4 - SDI
5 - CV+YC
6 - VGA scaler
7 - DVI
2
1 - for audio O0=0 – Unbalanced audio
O0=1 – Balanced audio
O1=0 – Digital audio
O1=1 – Analog audio
O4=0, O3=0, O2=0-Mono
O4=0, O3=0,O2=1-Stereo
9 VIDEO / AUDIO TYPE SETTING
2 - for VGA and DVI 1 - 640X480
2 - 800X600
3 - 1024X768
10 REQUEST VIS SETTING Set as SETUP #, or
set to 126 or 127 to
request if machine has
this function
0 - VIS source
1 - Input # or output # of source
2 - Vertical sync freq (Hz)
3, 4, 6, 7
11 REQUEST BREAKAWAY
SETTING
Set as SETUP #, or
set to 126 or 127 to
request if machine has
this function
0 - Request audio breakaway
setting
1 - Request “FOLLOW” setting
3, 4, 6, 15
12 REQUEST VIDEO / AUDIO
TYPE SETTING
Set as SETUP #, or
set to 126 or 127 to
request if machine has
this function
0 - for video
1 - for audio
2 - for VGA
3, 4, 6
13 SET HIGHEST MACHINE
ADDRESS
0 - for video
1 - for audio
Set equal to highest machine
address
2
14 REQUEST HIGHEST MACHINE
ADDRESS
0 - for video
1 - for audio
0 4
15 REQUEST WHETHER SETUP
IS DEFINED / VALID INPUT IS
DETECTED
SETUP #
or
Input #
0 - for checking if setup is defined
1 - for checking if input is valid
8