Alliance Laundry Systems UW35B2 - Manual (Page 8)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232168 6
Setup Mode (For Models With Firmware ID
Code “o2HC”, “o2UC”, “ouHC” and
“ouUC”)
NOTE: In Setup Mode, certain machine functions
can be configured. The settings in this mode are
related to how the machine is equipped from the
factory. Usually, these would not be changed in this
field.
NOTE: Enter Setup Mode through the Program Mode.
1. Press (*) key. Display will show “FAr” or “CEL”.
NOTE: This selects whether temperatures display
in degrees Fahrenheit (F) or Celsius (C), if control
is equipped with a temperature sensor. Press the
(
∧
) or (
∨
) key to change.
NOTE: Changing degrees “FAr” or “CEL” only
has an effect if the control has a temperature probe
connected and/or heat capability.
2. Press START key.
3. Model will display “HEAt” or “noHt”. Change
the selection by pressing the (
∧) or (∨) key.
4. Press START key to continue to the next step.
NOTE: If set for “HEAt”, the control has heat
capability enabled. The washer-extractor MUST
have electric or steam heat, and a temperature
probe. If display shows “noHt”, or if the message
“HEAt” or “noHt” does NOT display, the control
does NOT have heat capability.
5. Certain models will display “EFIL” or “ESUP”.
For these models, the control provides a spare
output (for certain models). The spare output can
be set up to control an extra fill valve (“EFIL”),
with the ability to fill to a programmable water
level (just as for regular fills), OR the spare
output can be set up to control an extra chemical
supply signal (“ESUP”).
6. Press START keypad.
7. Certain models display “bEEP” (control sounds
beeper during Add Bleach [Supply 2]) or “nobP”
(control does NOT sound beeper during Add
Bleach [Supply 2]). Change selection by pressing
(
∧) or (∨) keypad.
8. Press START keypad.
NOTE: If “EFIL” or “ESUP” does NOT display,
the extra fill capability is NOT present. If either
message does display, change the selection by
pressing the (
∧) or (∨) key. Press START key to
return to Program Mode. Refer to “Programming
Cycle Segments” section for additional information.
9. “Adv” or “noAd” will display. If “Adv” is set,
control will advance to the next step when up
arrow keypad is pressed during a regular cycle. If
“noAd” is set, control cannot advance during a
regular cycle, but can advance during the factory
test cycle when up arrow keypad is pressed.
10. Press START (enter) keypad to continue to next
step.
11. “PtIM” or “EtIM” will display. “PtIM” means
control will not display remaining time in a cycle.
“EtIM” means control will display an estimated
remaining time for a fill and drain. Press the up
or down keypad to change “PtIM”/ “EtIM”
selection.
12. Press START (enter) keypad to continue to the
next step.
Cycle and Error Count
1. To read, enter Program Mode. Refer to Entering
Program Mode.
2. Press START (enter) keypad. Display shows
“Erdn” (indicates Drain Error count).
3. Press START (enter) keypad. Display shows a
number (2 or 3 digits) showing how many drain
errors have occurred. This number can range
from ‘00’ to ‘255’, and cannot be set to zero.
4. Press START (enter) keypad. Display shows
“ErFL” (indicates Fill Error count).
5. Press START (enter) keypad. Display shows a
number (2 or 3 digits showing how many fill
errors have occurred. This number can range
from ‘00’ to 255’, and cannot be set to zero.
6. Press START (enter) keypad. Display shows
“CYC “ (indicates Cycle count).
7. Press START (enter) keypad. Displays show a
number (up to 4 digits) showing how many
complete cycles have been operated. This
excludes cycles stopped because of an error.
8. Press START (enter) keypad.
9. If display does not show “E Pr”, control will
revert to normal program mode.
10. If display shows “E Pr”, this is for factory
reference regarding power interruption. Press
START (enter) keypad. A number will display.
Press START (enter) keypad. After a brief pause,
the control will display normal program mode.