Toshiba SV685 - Manual (Page 50)

50
CONTROLS AND FEATURES
In order to receive sound from a connected PC, plug the
audio cable into the back of the television (as shown in the
‘Connecting a computer’ section), and then use the PC/
HDMI 1 Audio setting.
a
In the SETUP menu, press b until AV Connection is
highlighted, and then press Q .
b
Highlight PC/HDMI 1 Audio, and then use c to select
the PC option.
NOTE: Selecting the PC option will force HDMI 1
Audio to Digital mode.
If the connected HDMI source does not support digital audio,
plug the audio cable into PC/HDMI 1 (AUDIO) on the back of
the television (as shown in the ‘Connecting an HDMI™ or DVI
device to the HDMI input’ section), then use the HDMI 1
Audio setting.
a
In the AV Connection menu, press b to highlight PC/
HDMI 1 Audio and using c select HDMI 1.
b
Then highlight HDMI 1 Audio, and using C or c
select Auto or Analogue.
If the sound is absent, try selecting a different setting.
NOTE: HDMI 1 supports digital and analogue sound,
HDMI 2, HDMI 3 and HDMI 4 are digital sound only.
Certain DVD disk formats may not output from this TV
(32/44.1/48kHz and 16/20/24 bits are
acceptable).
Some early HDMI equipment may not work properly with
your HDMI TV. Please try setting the Lip Sync and
INSTAPORT™ options to Off. Adjusting these settings should
allow your early HDMI source to operate properly with your
television.
a
In the SETUP menu, press b until AV Connection is
highlighted, then press Q .
b
Press b to highlight HDMI Settings and press Q .
NOTE: HDMI Settings is grayed out on non-HDMI
inputs.
c
Press B or b to select an item, and then press C or
c to select a setting.
• Lip Sync: On
This option activates an audio/video display timing
adjustment function that allows HDMI source
devices to accurately perform synchronization
automatically.
• INSTAPORT™: On
This feature reduces the lag time when switching
HDMI sources.
• RGB Range: Auto
This feature adjusts RGB full range signal
automatically. When Limit is selected, RGB signal is
output in the range from 16 to 235. When Full is
selected, RGB signal is output in the range from 0
to 255.
NOTE:
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 50Hz or
supports Deep Colour, you will need a Category 2 cable.
Conventional HDMI/DVI cables may not work properly
with this mode.
• All of the above HDMI settings need proper HDMI source
devices.
If the HDMI source products do not support these features,
the television may not work properly by activating these
features.
When connecting a surround sound amplifier to the digital
audio output (Sony/Philips Digital Interface Format
[S/PDIF]), the following options can be selected.
PCM: this mode outputs PCM format to the digital audio
output socket.
Auto: this mode outputs Dolby Digital (if available) or PCM to
the digital audio output socket.
Dolby Digital S Dolby Digital
Dolby Digital Plus S Dolby Digital
MPEG S PCM
HE-AAC S Dolby Digital
a
In the AV Connection menu, press b to select Digital
Audio Output .
b
Use C or c to select PCM or Auto.
PC Audio
HDMI 1 Audio
HDMI Settings
Woofer Internal
AV Connection
PC/HDMI 1 Audio
HDMI Settings
HDMI 1 Audio
EXT 2 Input
Digital Audio Output
Auto
AV
Auto
HDMI 1
Digital Audio Output
HDMI Settings
INSTAPORT TM
Lip Sync
RGB Range
On
On
Auto
HDMI, the HDMI logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC.
INSTAPORT™ and INSTAPORT logo are trademarks of
Silicon Image, Inc. in the United States and other countries.