Sharp DK-KP85PH - Manual (Page 28)

E-19
Using the Radio Data System (RDS) (continued)
■ Using the Auto Station Programme
Memory (ASPM)
While in the ASPM operation mode, the tuner will
automatically search for new RDS stations. Up to 40
stations can be stored.
If you have already stored some stations in memory, the
number of new stations you can store will be less.
1 Press the TUNER button on the remote control or
FUNCTION button repeatedly on the main unit to
select TUNER function.
2 Press and hold down the RDS ASPM button on the
remote control.
1 After “ASPM” has flashed for about 4 seconds,
scanning will start (87.50 - 108.00 MHz).
2 When an RDS station is found, “RDS” will appear
for a short time and the station will be stored in
memory.
3 After scanning, the number of stations stored in
memory will be displayed for 4 seconds, and then
“END” will appear for 4 seconds.
To stop the ASPM operation before it is complete:
Press the RDS ASPM button while it is scanning for stations.
The stations which are already stored in memory will be
kept there.
Notes:
● If the same station is broadcasting on different
frequencies, the strongest frequency will be stored in
memory.
● Any station which has the same frequency as the one
stored in memory will not be stored.
● If 40 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
● If no station has been stored in memory, “END” will
appear for a short while.
● If the RDS signals are very weak, station names may
not be stored in memory.
● The same station name can be stored in different
channels.
● In a certain area or during certain time periods, the
station names may temporarily be different.
■ Notes for RDS operation
If any of the following events occur, it does not mean
that the unit is faulty:
● “PS”, “No PS” and a station name appear alternately,
and the unit does not operate properly.
● If a particular station is not broadcasting properly
or a station is conducting tests, the RDS reception
function may not work properly.
● When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
● “No PS”, “No PTY” or “No RT” will flash for about 5
seconds, and then the frequency will be displayed.
Notes for radio text:
● The first 14 characters of the radio text will appear for
4 seconds and then they will scroll across the display.
● If you tune in to an RDS station which is not
broadcasting any radio text, “No RT” will be displayed
when you switch to the radio text position.
● While radio text data is received or when the text
contents change, “RT” will be displayed.
■ To recall stations in memory
To specify programmed types and select stations
(PTY search):
You can search a station by specifying the programme
type (news, sports, traffic programme, etc. ...see page 20)
from the stations in memory.
1 Press the TUNER button on the remote control or
FUNCTION button repeatedly on the main unit to
select TUNER function.
2 Press the RDS PTY button on the remote control.
“SELECT” and “PTY TI” will appear alternately for about
6 seconds.
3 Within 6 seconds, press the TUNING ( or ) button to
select the programme type.
Each time the button is pressed, the programme type will
appear.
4 While the selected programme type is flashing (within
6 seconds), press the RDS PTY button again.
After the selected programme type has been lit for
2 seconds, “SEARCH” will appear, and the search
operation will start.
Notes:
● If the display has stopped flashing, start again from
step 2. If the unit finds a desired programme type,
the corresponding channel number will lit for about 8
seconds, and then the station name will remain lit.
● If you want to listen to the same programme type of
another station, press the RDS PTY button while the
channel number or station name is flashing. The unit
will look for the next station.
● If no station can be found, “Not Found” will appear
for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 3, “TP”
will appear.
(This does not mean that you can listen to the traffic
information at that time.)
When the traffic information is broadcast, “TA” will
appear.