Connections, Connecting a composite video source to port 1, Connecting a s-video or video source to port 2 – Barco R9002240 User Manual

Page 13: 4 pin connector configurations

Advertising
background image

Connections

3-3

5975688 BARCOVISION 1609S 131097

Connecting a Composite Video source to port 1.

Composite video signals from a VCR, OFF air signal decoder, etc..

Video input selection :

with the RCU or the build in RCU : press digit button 1

* Note : if using the loop-through Video output, then set the

Termination Switch to the "OFF" position.

Connecting a S-Video or Video source to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.

Highlight Port 2 : Video and press ENTER to toggle between VIDEO

or S-VIDEO.

Press EXIT to return.

Press ADJUST to return to operational mode.

Select with or

then <ENTER>

<EXIT> to return.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

IRIS

Source 02

Select with or

then <ENTER>

<EXIT> to return.

Choose a setup pattern

from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 02

Select with or

then <ENTER>

<EXIT> to return.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

CONTR. MODULATION

SOFT EDGE

Select with or

<ENTER> to accept

<EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PORT2 : S-VIDEO

LINE DOUBLER : ON

Highlight 'Picture Tuning' and press ENTER.

Select 'Selected source' and press ENTER.

Input selection

with the RCU or the build in RCU : press digit button 2

Depending on the priority setting in the Picture Tuning menu,

Video or S-Video can be displayed.

If the setting is not correct, start up the adjustment mode by

pushing on th ADJUST key.

Select 'Random Access' and press ENTER.

* Note: When using the Port 2 loop-through output, set the Termination

Switch in the "OFF" position.

1

2

3

4

4 pin connector configurations:

For S-video:

Pin 1: earth(ground) luminance

Pin 2: earth(ground) chrominance

Pin 3: luminance signal(Y)

1Vpp

±

3dB

Pin 4: chrominance signal(C)

300mVpp

±

3dB

For video:

Pin 1: earth(ground) video

Pin 2: not connected

Pin 3: video signal

Pin 4: not connected

UWLjr…ÃrtÃUW9H#Ƈr…r‚

W8S

6ˆqv‚Ãh€ƒyvsvr…

8‚€ƒ‚†v‡rÃ

‰vqr‚

U‚Ár‘‡Ãƒ…‚wrp‡‚…

&$Âu€

PAA

PI

QPSUÃ

WD9@P

QPSUÃ#$

SB7ÃÃCW

Wƒp

S

B

7

QPSUÃ%ÃS@HPU@

8PHHVID86UDPI

QSPE@8UPSÃHP9@

QPX@SH6DIT

QPSUÃ!

TWD9@P

&$Âu€

PI

PAA

BS@@IГ)Г‚ƒr…h‡v‚hy

S@9Г)Г†‡hqi’

QPSUÃ"

8‚€ƒCƒp

W8SÃTWCT

6ˆqv‚Ãh€ƒyvsvr…

Gˆ€h8u…‚€h

‡‚Ár‘‡Ãƒ…‚wrp‡‚…Â…

‡‚ÃhÀ‚v‡‚…

&$Âu€

PAA

PI

QPSUÃ

WD9@P

QPSUÃ#$

SB7ÃÃCW

Wƒp

S

B

7

QPSUÃ%ÃS@HPU@

8PHHVID86UDPI

QSPE@8UPSÃHP9@

QPX@SH6DIT

QPSUÃ!

TWD9@P

&$Âu€

PI

PAA

BS@@IГ)Г‚ƒr…h‡v‚hy

S@9Г)Г†‡hqi’

QPSUÃ"

8‚€ƒCƒp

Advertising
This manual is related to the following products: