Intelix AVO-SVA2 - Manual

Specifications
Specifications subject to change without notice.
Maximum Distance* 1000 feet
Maximum Input 1.1 Vp-p
Bandwidth (video) DC to 6 MHz
Bandwidth (audio) 20 Hz to 20 kHz
Impedance (video) 75 ohms
Impedance (audio) 600 ohms minumum
Insertion Loss Less than 2 dB per pair over the frequency range
Return Loss Greater than 15 dB over the frequency range
Common Mode Rejection Greater than 40 dB over the frequency range
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors One (1) S-Video 4-pin and two (2) RCA to one (1) RJ45
RJ45 Pinout S-Video Luma: 7 & 8, pair 4
S-Video Chroma: 4 & 5, pair 1
Audio 1: 1 & 2, pair 2
Audio 2: 3 & 6, pair 3
Temperature Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95%
Enclosure Black plastic
Dimensions 4.3” x 2.5” x 1”
Weight 0.2 lbs (3.2 oz.)
Ordering Information AVO-SVA2: single AVO-SVA2 balun in bulk packaging
AVO-SVA2-PAC: two AVO-SVA2 baluns in retail-ready packaging
Warranty 2 years
* Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, and cable patches. Intelix specifications are
based on straight-through cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix AVO-SVA2 S-Video and Audio Balun
Ins Ins Ins Ins Inst tt ttallation Manual allation Manual allation Manual allation Manual allation Manual
The AVO-SVA2 balun allows the transmission
of a single S-Video signal and two analog audio
signals over unshielded twisted pair (UTP) cable,
such as Cat 5. Used in pairs, SVA2 baluns
eliminate costly and bulky S-Video cable,
allowing the connection of S-Video equipment
to any convenient modular outlet.
The SVA2 balun allows pre-existing twisted pair
cable to be used in such applications as
classroom video distribution, overhead projector
systems, PC-training systems, and tradeshow PC-demo systems in the S-Video environment.
To install an AVO-SVA2 balun, perform the following steps:
1. Turn off power and disconnect the S-Video source and S-Video monitor.
2. Make certain the modular outlets and cross connects to which you will connect the
AVO-SVA2s are configured properly and labeled appropriately to identify the circuit.
3. Verify the desired twisted pairs are not used with other LAN or telephone equipment.
4. Connect the balun to the S-Video port of the source equipment (i.e., DVD or VCR).
Connect the audio connectors to the audio source.
5. Connect a 4-pair Cat 5 cable from the RJ45 8-position modular jack of the AVO-
SVA2 to a structured cable, such as Cat 5.
6. Connect the second balun’s RCA inputs to the destination equipment.
7. Connect the 4-pair Cat 5 cable from the RJ45 8-position modular jack of another
AVO-SVA2 to the structured cable attached to the first balun.
8. Power on the S-Video equipment at both ends and adjust the monitor image and audio
levels to the desired settings.
Installation
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the AVO-SVA2. Opening the unit will void your warranty.
Caution: Do not connect the AVO-SVA2 to a telecommunication outlet wired to
unrelated equipment. Making such a connection may damage the equipment
and/or balun. Please ensure all wiring is “straight-through.”
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
AvoCat
Series