Klein Tools MM200 - Manual (Page 2)

Designer/Production: Sandra ex 15612
Client Contact: Chris Trott, ex 13267
Client Sign off:
ENGLISH
FIle Name: MKT121707-MM200-Multimeters-139572TART
Product: MM200
Package Part #: 139572T
Date: 3/01/10
a. B. Use properly safety-rated leads.
a.
do not attempt to measure more than 600V or 400ma.
B. do not attempt to measure more than 10a.
C. Select Functionality Button
• Switch between AC and DC.
• Switch between
and .
d. data Hold
• Press to hold the current input on the display.
• Press again to return to live reading.
E. Select Frequency/duty Cycle Button
• Switch between measurement, Hz, and %.
FUNCTION INSTRUCTIONS
• Do not attempt to measure resistance on a live circuit.
5. diode/Continuity
CATIII
COM
m
10A/500V ~ 400mA/250V ~
600V MAX
Temp
FUNC. HOLD
MM200
H z%
mA
A
µA
Temp
H z%
B
C
On Back
E
a
H z%
H z%
mA
A
µA
Temp
H z%
mA
A
µA
Temp
H z%
H z%
COM m
10A/250V ~ 400mA/250V ~ 600V MAX
Temp
Hz%
mA
A
µA Temp
COM m
10A/250V ~ 400mA/250V ~
600V MAX
Temp
Hz%
mA
A
µA Temp
COM m
10A/250V ~ 400mA/250V ~ 600V MAX
Temp
Hz%
mA
A
µA
Temp
COM m
10A/250V ~ 400mA/250V ~ 600V MAX
Temp
Hz%
mA
A
µA
Temp
COM m
10A/250V ~ 400mA/250V ~ 600V MAX
Temp
Hz%
mA
A
µA
Temp
COM m
10A/250V ~ 400mA/250V ~ 600V MAX
Temp
Hz%
mA
A
µA Temp
F. Backlight
• Press to enable/disable lights.
• Using lights drains the battery significantly.
G. H. Battery/Fuse Replacement
• When indicator is displayed on the LCD, batteries must be
replaced.
• Remove back screw and replace 9V battery.
• If more than 400mA is applied to
a , replace with 400mA/250V
fast-blow fuse.
• If more than 10A is applied to B , replace with respective
10A/500V fast-blow fuse.
auto Power-Off
• Device will power off after 15 minutes non-use.
• Turn the dial or press a button to wake.
H
F
d
G
FEaTURE dETaILS
MM200
Instruction Manual
GENERaL SPECIFICaTIONS
The Klein Tools MM200 is an auto-ranging multimeter. It measures
AC / DC voltage, AC / DC current, resistance, capacitance, temperature,
and frequency. It can also test diodes and continuity.
• Operating altitude: 2000 meters
• Relative Humidity: 75% max operating
• Operating Temperature: 0°C / 32°F to 40°C / 104°F < 75% R.H.
• Storage Temperature: -20°C / -4°F to 60°C / 140°F < 80% R.H.
• accuracy Temperature: 18°C / 64°F to 28°C / 82°F < 75% R.H.
• Temperature Coefficient: 0.1*(specified accuracy) / °C
• Sampling Frequency: 3 samples per second
• dimensions: 5.91" x 2.76" x 1.97"
• Weight: 8.36 oz.
• Calibration: Accurate for one year
• CaT Rating: CAT III 600V
• Listing: ETL & cETL standard UL 3111-1 listed
• Pollution degree: 2
• accuracy: ± (% of reading + # of least significant digits)
WaRNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring
a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms, or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from
the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes
are connected.
• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock,
replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out
power before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
• Select AC or DC voltage source.
2. aC / dC Current (large): < 10a
1. aC / dC Voltage: < 600V
• Start with this setting if current level is unknown.
• Attach red lead to “10A” input.
• Select AC or DC current source.
• Current above 10A will require fuse replacement.
Diode:
Display shows:
• Forward voltage drop if
forward biased.
• “O.L.” if reverse biased.
3. aC/dC Current (small): < 400ma
• Attach red lead to “mAμA” input.
• Select μA or mA, and AC or DC current source.
• Current above 400mA will require fuse replacement.
4. Resistance: < 40M Ω
SyMBOLS
~
aC alternating Current Warning or Caution
dC direct Current dangerous Levels
dC/aC Voltage or Current double Insulated Class II
Ground aC Source
FUNC.
PRESS
FUNC.
PRESS
AC DC
FUNC.
PRESS
AC DC
FUNC.
PRESS
AC DC
Continuity:
• Display shows resistance.
• Buzzer sounds if less than 50
Ω .
H z%
mA
A
µA
Temp
3
5
6
2
1
4
7
8
MM200-Instructions-139572TART.indd 5-8 6/3/10 8:41 AM