Tweco XT-301 Torch Data for Distributor Use w- Auto-Cut 20 O2 AG - Manual (Page 12)

Torch Data 8-12 Manual 0-4821 Rev. AG
Stainless Steel
100A
N
2
Plasma / H
2
O Shield
(ga) (in) inch psi Ball* psi Ball* psi Volts
(in)
±0.005
(ipm) (in) (sec) (in)
10 0.141 80 60 120 5 55 156 0.125 160 0.200 0.000 0.074
3/16 0.188 80 60 120 5 55 158 0.125 100 0.250 0.300 0.080
1/4 0.250 80 60 120 5 55 165 0.125 60 0.250 0.300 0.086
3/8 0.375 80 60 120 5 55 173 0.125 50 0.250 0.300 0.087
1/2 0.500 80 60 120 5 55 179 0.130 35 0.300 0.500 0.100
5/8 0.625 80 60 120 5 55 181 0.140 30 0.300 0.600 0.110
3/4 0.750 80 60 120 5 55 185 0.150 25 0.120
bar Ball* bar Ball* bar Volts
(mm)
±0.1
(mm/min) (mm) (sec) (mm)
5.5 60 8.3 5 3.8 155 3.2 4810 4.5 0 1.8
5.5 60 8.3 5 3.8 157 3.2 3530 5.5 0.1 1.9
5.5 60 8.3 5 3.8 159 3.2 2400 6.4 0.3 2.1
5.5 60 8.3 5 3.8 163 3.2 1750 6.4 0.3 2.2
5.5 60 8.3 5 3.8 169 3.2 1390 6.4 0.3 2.2
5.5 60 8.3 5 3.8 174 3.2 1210 6.5 0.3 2.3
5.5 60 8.3 5 3.8 178 3.3 970 7.3 0.5 2.5
5.5 60 8.3 5 3.8 180 3.5 800 7.6 0.6 2.7
5.5 60 8.3 5 3.8 186 3.9 600 3.0
* Ball setting for shield water is set using customer line pressure of 55 psi / 3.8 bar
Bold type indicates maximum piercing parameters. Bold italic indicates edge starts only.
Edge Start
Kerf
Width
@ Rec.
Speed
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf
Width
@ Rec.
Speed
5
15
20
6
8
10
12
(mm)
3
4
Shield (H
2
O)
100A Stainless Steel (N
2
/H
2
O)
Material
Thickness
Arc
Voltage
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Cut Flow Rates / Pressures
Plasma (N
2
) Shield (H
2
O)
NOTE: Ohmic height sensing is not recommended with water shield. Water on the plate interferes
electrically with the ohmic sensing system.
Pre Flow
Pressure
(N
2
)
Pre Flow
Pressure
(N
2
)
Material
Thickness
Arc
Voltage
Torch
Working
Height
Edge Start
Cut Flow Rates / Pressures
Plasma (N
2
)
Electrode
35-1034 35-1272 35-1053 35-1041 35-1089
Cartridge
35-1020
Shield Cup
35-1016 Plasma Gas Distributor Shield Gas Distributor Tip Shield Cap
Art # A-07297