Great Plains NTA3007HD Operator Manual - Manual (Page 15)

Appendix Front Page Part Lists Great Plains Manufacturing, Inc. 15
02/21/2012 Front Page Part Lists 166-367M
Part Lists
New Parts
The part call-out numbers in this list match all Figures in
these installation instructions. Part descriptions match
those in your updated Parts Manual. Quantities are units (“ea”).
166-366A Kit Contents
Other Parts
Existing Parts Affected
The following existing parts are involved in the kit instal-
lation. The Disposition column indicates whether the part
is left in place, moved or not re-used. The part call-out numbers in the list matches all Figures
in the installation instructions. The descriptions match
those in your air drill Parts manual.
Callout Quantity Part Number Part Description
11 1 166-367M MANUAL NTA 907 CONT DR UPDA
12 4 188-006V BEARING .880 HEX BORE 205DD
13 4 266-294D CONTACT WHL DOWN STOP
14 2 266-295D CONTACT WHL PVT TUBE
15 2 266-296D CONTACT WHEEL PIVOT SHAFT
16 2 402-266D 7/8 HEX SHAFT SPACER TB X 9
17 2 804-061C WASHER MACH 1.50 X 1.00 X 1
18 4 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT
Callout Quantity Part Number Part Description
19 1 821-001C PAINT GP GREEN SPRAY CAN
Callout Qty Part No. Part Description Part Disposition
51 2 136-259D CHAIN RL #50 117 PITCHES Removed and re-installed.
52 2 136-260D CHAIN RL #50 144 PITCHES Removed and re-installed.
53 2 166-196H ARM PARALLEL W/ SPNG BRKT WELD Modified in place.
54 1 166-201H CONTACT DRIVE WELDMENT RIGHT Removed and re-installed.
55 1 166-205H CONTACT DRIVE WELDMENT LEFT Removed and re-installed.
56 2 166-953D HEX SHAFT 7/8X20.56 LONG Removed. Not re-used.
57 2 266-003D SHAFT 7/8 HEX 32.75 Removed and re-installed.
58 4 266-250D TUBE RND 1OD X 7/32W X 1.44 L Removed and re-installed.
59 4 802-226C HHCS 1/2-13X2 3/4 GR5 Removed and re-installed.
60 6 802-282C RHSNB 5/16-18X1 GR5 Removed and re-installed.
61 4 803-020C NUT HEX 1/2-13 PLT Removed and re-installed.
62 12 803-177C NUT HEX FLG TP LK 5/16-18ZNYCR Removed and re-installed.
63 2 804-015C WASHER LOCK SPRING 1/2 PLT Removed and re-installed.
64 4-8 804-061C WASHER MACH 1.50 X 1.00 X 18GA Removed and re-installed.
65 8 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT Removed. Not re-used.
66 4 807-055C SPRING HOLD DOWN HD COULTER Disconnected and re-connected.
67 2 808-311C SPKT 50C27 X 7/8 HEX BORE Removed and re-installed.
68 4 808-319C SPKT 50C30 X 7/8 HEX BORE Removed and re-installed.
69 4 814-134C TIRE/WHEEL ASSY 13/5 X 6 Removed and re-installed.
70 4 822-119C BRG 7/8HEXX2.05OD SPH Removed and re-installed.
71 8 822-175C FLANGETTE 52 3-BOLT PLT Removed and re-installed.