Hitch truss & h-bracket, Hitch assembly, Hitch truss & h-bracket hitch assembly – Great Plains 1500TM Predelivery Manual User Manual

Page 13

Advertising
background image

Great Plains Manufacturing, Inc.

Assembly

9

12/12/2013

586-535Q

Hitch Truss & H-Bracket

Refer to Figure 7

21. Align holes on truss plates

and center frame plates.

Install the 3/4 x 2 hex bolts

(front and rear plates) and

3/4 x 2 1/2 hex bolts

(middle plates), 3/4 lock washers

and 3/4 nuts of trusses

.

22. Align rear holes of level bar

between ears of torque

tube, secure the 1 x 9 1/2 pin

. Align hole in pin with

holes in torque tube collar, secure with the 3/8 x 2 1/4
Gr. 8 hex bolt

and 3/8 nylon lock nut.

23. Align holes in rear plate of h-bracket spring assembly

and front plate of level bar

, secure with 3/4 x 2 Gr. 8

hex bolts

, 3/4 lock washers and 3/4 nuts.

24. Align bottom holes on h-bracket spring assembly

with

ears on front of center frame, secure with 1 x 3 1/4
usable pins

, 1.5 x 1.0 x.075 machine washers

and

3/16 x 2 cotter pin.

25. Bolts may be tightened to specs, See “Torque Values

Chart” on page 19.

Hitch Assembly

Refer to Figure 8
26. Remove the 1 1/4 x 8 Gr. 8 bolts

from the rear of hitch

assembly

. Bolt the hitch assembly

to center frame

with the 1 1/4 x 8 Gr. 8 bolts

, 1 1/4 flat washer

(one

side of uniball to take up space) and 1 1/4 top lock nuts.
Tighten bolts snug, do not torque, as the hitch must pivot
freely.

27. Install jack

on front outside of hitch to support the front

of hitch

for the rest of assembly.

28. Remove 1 1/4 x 8 1/2 Gr. 8 special thread bolt

from

front short level bar tube

. Align holes in rear of level

bar tube

and center hole of h-bracket

. Install the 1

1/4 x 8 1/2 Gr. 8 special thread bolt

from the left side

and secure with 1 1/4 top lock nut.

29. Bolt the spring hose holder

to welded nut on front of

hitch with 1/2 x 1 Gr. 5 bolt

, 1/2 flat washer and 1/2

lock washer.

30. The front of the level turnbuckle

may need attached to

ears on hitch assembly

with 1 x 6 hex bolt

and 1

top lock nut

31. Bolts may be tightened to specs, See “Torque Values

Chart” on page 19.

7

2

U

D

F

B

L

R

4

2

6

Figure 7

Truss & H-Bracket

42869

1

9

1

5

8

3

10

1

2

3

1

4

5

6

7

4

8

7

9

10

Figure 8

Hitch

42388

3

4

1

6

2

8

9

7

5

U

D

F

B

L

R

3

10

11

2

1

1

2

3

4

1

5

6

6

7

5

8

9

10

1

11

Advertising
This manual is related to the following products: