5109-5315 center fold, 5317-5323 center fold, 5109-5315 center fold 5317-5323 center fold – Great Plains TC5319 Assembly Manual User Manual

Page 18

Advertising
background image

14

TC5109-5323

Table of Contents

Index

Great Plains Manufacturing, Inc.

566-046E

Table of Contents

Index

04/12/2012

5109-5315 Center Fold

Refer to Figure 11
55. Install center fold bracket

and rebound valve

bracket

to front center frame plate with 3/4 x 2 1/2

hex bolts

, 3/4 lock washers and 3/4 nuts.

56. Attach center wing stop

(Models 5313 & 5315 only)

to truss plates with 5/8 x 1 1/2 hex bolts

, 5/8 lock

washers and 5/8 nuts.

57. Attach wing pivot

plates on side of center frame

with 3/4 x 2 1/2 hex bolts

, 3/4 x 3 1/2 hex bolts

(front wing pivot plates, lower holes only), 3/4 lock
washers and 3/4 nuts.

58. Attach 12ga

16ga

shim’s as needed with 3/4 x 2

1/2 hex bolts

, 3/4 lock washers and 3/4 nuts to

level wings.

Note: See “Operator’s Manual” general operation and in-

field adjustment section for adjustment procedure.
Attach extra shim’s to the lower front 3/4 x 3 1/2 hex
bolts

, secure with 3/4 lock nuts

.

59. Models 5109-5115 attach rigid smv & light bracket

to rear truss plates with 5/8 x 1 1/2 hex bolts

,5/8

lock washers and 5/8 nuts.

60. Attach SMV sign

to either center wing stop

or

rigid smv & light bracket

with 1/4 x 3/4 pan head

screws

, 1/4 lock washers and 1/4 hex nuts.

61. Models 5313-5315 attach rebound valve

with 5/16

x 4 hex bolts

, 5/16 lock washers and 5/16 nuts.

62. Tighten all bolts to specs, See “Torque Values Chart

on page 27.

5317-5323 Center Fold

Refer to Figure 12
63. Install front center fold bracket

and rear center fold

bracket

to center frame plates with 3/4 x 2 1/2 hex

bolts

, 3/4 lock washers and 3/4 nuts.

64. Attach center wing stop

to truss plates with 5/8 x 1

1/2 hex bolts

, 5/8 lock washers and 5/8 nuts.

65. Attach wing pivot

plates on side of center frame

with 3/4 x 2 1/2 hex bolts

, 3/4 lock washers and 3/4

nuts.

66. Attach SMV sign

to center wing stop

with 1/4 x 3/

4 pan head screws

, 1/4 lock washers and 1/4 hex

nuts.

67. Tighten all bolts to specs, See “Torque Values

Chart” on page 27.

Figure 11

5109-5315 Center Fold

42630

1

4

5

6

U

D

F

B

L

R

8

7

3

9

18

15

12

13

2

7

16

14

17

3

10

1

2

3

4

5

6

7

12

8

9

10

12

18

13

5

14

4

13

15

16

17

Figure 12

5317-5323 Center Fold

42631

3

5

7

U

D

F

B

L

R

1

4

6

9

6

2

3

8

1

2

3

4

5

6

7

8

4

9

Advertising