Great Plains 2525P Parts Manual - Manual (Page 47)

Revision Comments Part Description Part No. Ref.
Image No. dwg22698
25 SERIES OPENER SHANK WELDMT 298-509H 1.
HHCS 3/8-16X2 1/2 GR5 802-114C 2.
HFS 1/2-13X6 1/8GR5 PLT 802-745C 3.
IDLER SPOOL 1.44OD X.53B X1.5L 817-480C 4.
IDLER SPACER TUBE 1/2OD X 1.56 198-257D 5.
NUT FLANGE LOCK 3/8-16 PLT 803-209C 6.
25P CENTER MIDDLE OPENER MOUNT 298-626H 7.
NUT HEX FLG. LOCK 1/2-13 PLT. 803-169C 8.
25P UPPER SPRING LINK 198-292D 9.
S/N 1503SS- 25 SERIES UPPER PARALLEL ARM 298-513H 10.
S/N 1504SS+ 25 SERIES UPPER PARALLEL ARM 288-374H 10.
SPRING EXT 1.575O.D.X.225 WIRE 807-076C 11.
25P LOWER SPRING LINK 198-293D 12.
25P REAR OPENER INNER PIVOT TB 198-295D 13.
S/N 1503SS- 25 SERIES LOWER PARALLEL ARM 298-510H 14.
S/N 1504SS+ 25 SRS LOWER PARALLEL ARM 403-667D 14.
2008- SPKT 41B12 7/8 HEX W/BEARING 403-059D 15.
2009+ PEER 7/8 HEX BRG AND MNT 822-239C 15.
HHCS 3/8-16X1 GR5 802-017C 16.
Used on front stagger on 9 1/2", 10",
twin row & twin row splitters 1ST
REVISION
RPBY 298-883S 298-514H 17.
2nd Revision 25P FRONT OPENER MOUNT W/BUSH 298-883S 17.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2 806-053C 18.
NUT HEX 5/8-11 PLT 803-021C 19.
DRIVE MOUNT WELDMENT 403-113H 20.
DRIVE PLATE LINE-UP PIN 403-107D 21.
Includes 46 - 52 DRIVE BEARING ASSEMBLY 403-117S 22.
RHSNB 3/8-16X1 GR5 802-015C 23.
HHCS 3/8-16X2 1/4 GR5 802-382C 24.
NUT HEX 3/8-16 PLT 803-014C 25.
WASHER LOCK SPRING 3/8 PLT 804-013C 26.
HHCS 3/8-16X1 GR5 802-017C 27.
SPRING COMP DIE.75X.375X1LX515 807-232C 28.
SCR HX SKT BUT CP 3/8-16X3/4 801-078C 29.
9/16 OD DRIVE PLATE SPACER TB 403-182D 30.
PRESS WHEEL ARM PIVOT BUSHING 817-083C 31.
IDLER BRACKET WELDMENT 403-115H 32.
IDLER PIVOT 2.06 LONG 891-191C 33.
IDLER 1 PC 2.38X1.01X1.062 817-406C 34.
SNAP RING EXT 1 HEAVY 800-085C 35.
WASHER FLAT 3/8 SAE PLT 804-012C 36.
WASHER GRASS SEEDER CUP SHAFT 804-042C 37.
METER ALIGNMENT BUSHING 403-108D 38.
METER RETAINER LATCH PLATE 403-112D 39.
METER RETAINER PLATE 403-111D 40.
SPRING EXT. 1.0ODX5.OLX.095MW 807-236C 41.
Used on front stagger rows on 15" &
20" spacing also used on all 30" rows
on 30" only spacing. Used on twin
row splitter openers.1st Revision
25P MIDDLE OPENER MOUNT W/BUSH 298-888S 42.
Used on rear stagger rows on 9 1/2",
10", 15", 20", twin row & twin row
splitters 2nd Revision
25P REAR OPENER MOUNT W/BUSH 298-887S 43.
Front row CHAIN RL #41 90 PITCHES 136-214D 44.
Middle row 7" stagger CHAIN RL #41 116 PITCHES 136-215D 44.
Rear row 14" stagger CHAIN RL #41 144 PITCHES 136-216D 44.
08/22/12 - 47 - 118-915P
Table of Contents Part Number Index
Openers
25 Series Opener Arms & Mounts
(Applies to 2525P (2006-) only)