Great Plains 2015 Operator Manual - Manual (Page 5)

-
3 4/18/05 Great Plains Mfg., Inc.
Section 1 Safety Rules
2015 Three-Point Soybean Machine 173-088M
Most accidents are the result of negligence and care-
lessness, usually caused by failure of the operator to
follow simple but necessary safety precautions. The fol-
lowing safety precautions are suggested to help prevent
such accidents. The safe operation of any machinery is
a big concern to consumers and manufacturers.Your 20’
3-Point Soybean Machine has been designed with many
built-in safety features. However, no one should operate
this product before carefully reading this Operators
Manual.
General Operation & Repair
1. Never allow the 20’ 3-Point Bean Machine to be operat-
ed by anyone who is unfamiliar with the operation of all
functions of the drill. All operators should read and thor-
oughly understand the instructions given in this manual
prior to moving the drill.
2. Make sure safety rules are understood before operating
machinery or tractor.
3. Never permit any persons other than the operator to ride
on the tractor.
4. Never permit any persons to ride on or stand near the
drill while it is in operation.
5. Regulate your speed to the field conditions, maintaining
complete control at all times.
6. After repairing or adjusting, make sure all tools and
parts are removed from the implement before attempting
to operate it.
7. Do not grease or oil machine while it is in operation.
8. Loose fitting clothing should not be worn as it may catch
in moving parts.
9. Never dismount from a moving tractor.
10. Do not leave the tractor or the implement unattended
with the engine running.
11. Do not stand between the tractor and the implement dur-
ing hitching.
12. Detach and store implements in an area where children
normally do not play. Stabilize implements by using suit-
able supports and block wheels.
13. If a hydraulic leak develops, correct it immediately. Es-
caping hydraulic oil can have extremely high pressure. A
stream of high pressure oil may easily penetrate the skin
as with modern needle-less vaccination equipment - but
with the exception that hydraulic fluid may cause blood
poisoning. It is imperative that the connections are tight
and that all lines and pipes are in good condition. If an
injury is caused by the escaping hydraulic fluid, see doc-
tor at once!
14. Use a piece of cardboard or wood to detect leaks of hy-
draulic oil under pressure.
15. Be sure to relieve all hydraulic pressure before disconnec-
tion any lines or pipes between the implement and the trac-
tor hydraulic system. Keep all guards and shields in place.
Transporting
1. Use good judgement when transporting tractor and im-
plements on the highway. Always maintain complete con-
trol of the drill.
2. Limit transport speed to 20 mph. Transport only with a
farm tractor of sufficient size and horse power.
3. Always make sure flashing safety lights, “Slow Moving
Vehicle” emblem, and reflectors are in place and visible
prior to transporting the drill on public roads.
4. Know your state and local laws concerning highway
safety and regulations. Comply with these laws when
transporting machinery.
5. Use warning flags or approved warning lights at night
and during other periods of poor visibility. Do your best
to prevent highway accidents.
Tire Handling & Repair
1. Tire changing can be dangerous and should be pre-
formed by trained personnel using the correct tools and
equipment.
2. Do not re-inflate a tire that has been run flat or seriously
under inflated. Have it checked by qualified personnel.
3. When removing and installing wheels, use wheel han-
dling equipment adequate for the weight involved.
Safety Decals
1. Your 20’ 3-Point Soybean Machine comes equipped with
all safety decals in place. They were designed to help you
safely operate your 20’ 3-Point Bean Machine. Read and
follow their directions.
2. Keep safety decals clean and legible.
3. Replace all damaged or missing safety decals. To order
new safety decals go to your Great Plains Dealer and refer
to the parts section for safety decal package part number.
4. Replace these decals whenever they become worn or un-
readable. To instal new safety decals:
a. Clean the area the decal is to be placed
b. Peel backing from the decal. Press firmly on to sur-
face being careful not to cause air bubbles under the
decal.
Section 1
Safety Rules
!