Dell 2407WFP Monitor - Manual (Page 47)

Card Reader Troubleshooting
2407WFP) l Confirm that the monitor has power.
l If the monitor has no power, see Monitor Specific Troubleshooting for monitor common
problem.
No Sound Soundbar has power - power
indicator is on. l Plug the audio line-in cable into the computer's audio out jack.
l Set all Windows volume controls to their maximum.
l Play some audio content on the computer (i.e. audio CD, or MP3).
l Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
l Clean and reseat the audio line-in plug.
l Test the Soundbar using another audio source (i.e. portable CD player).
Distorted Sound Computer's sound card is used
as the audio source. l Clear any obstructions between the Soundbar and the user.
l Confirm that the audio line-in plug is completely inserted into the jack of the sound card.
l Set all Windows volume controls to their midpoints.
l Decrease the volume of the audio application.
l Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
l Clean and reseat the audio line-in plug.
l Troubleshoot the computer's sound card.
l Test the Soundbar using another audio source (i.e. portable CD player).
Distorted Sound Other audio source is used. l Clear any obstructions between the Soundbar and the user.
l Confirm that the audio line-in plug is completely inserted into the jack of the audio source.
l Decrease the volume of the audio source.
l Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
l Clean and reseat the audio line-in plug.
Unbalanced Sound
Output Sound from only one side of
Soundbar l Clear any obstructions between the Soundbar and the user.
l Confirm that the audio line-in plug is completely inserted into the jack of the sound card or
audio source.
l Set all Windows audio balance controls (L-R) to their midpoints.
l Clean and reseat the audio line-in plug.
l Troubleshoot the computer's sound card.
l Test the Soundbar using another audio source (i.e. portable CD player).
Low Volume Volume is too low. l Clear any obstructions between the Soundbar and the user.
l Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume setting.
l Set all Windows volume controls to their maximum.
l Increase the volume of the audio application.
l Test the Soundbar using another audio source (i.e. portable CD player).
NOTICE: Do not remove the device while reading or writing media. Doing so may cause loss of data or malfunction in the media.
Problem Cause Solution
Drive letter is not assigned.
(Windows XP only)
Conflict with network drive letter.
A. Right-click My Computer on the desktop, and
then click Manage. Under Computer
Management, click Desk Management.
B. In the list of drives in the right panel, right-
click Removable Device and then click Change
Drive Letter and Paths.
C. Click Change, and in the drop-down box,
specify a drive letter for the Removable Device,
choosing one that is not assigned to the
mapped network drives.
D. Click OK, and then click OK again
Drive letter is assigned, but the
media is not accessible
The media needs reformatting.
Right-click the drive in Explorer and choose
Format from the resulting menu.
The media has been ejected during
writing or erasing.
Displays the error message, "Error copying file or folder."
Displays the error message, "Cannot write folder (folder name) or
file (file name)," during writing, or, "Cannot remove folder (folder
name) or file(file name),". While erasing, you cannot write or
erase in the same folder or file name.
Reinsert the media and write or erase again.
Format the media for writing or erasing the
same folder or file name.
Despite the disappearance of the
pop-up window, the media has been
ejected while the LED was blinking.
Although the pop-up window disappears during writing, if you
eject your media while the LED is still blinking, then you cannot
complete your action on the media.
Format the media for writing or erasing the
same folder or file name.
Cannot format or write on the
media.
Write protect switch is enabled.
Verify that the write
- protect switch of the media
is unlocked.