Dell OptiPlex G1 - Manual (Page 111)

Installing System Board Options 6-17
AC power. In this case, you must enter the System Setup program and reset the con-
figuration options.
Use the following procedure to replace the system battery with another CR2032 coin-
cell battery:
 ,I\RXKDYHQRWDOUHDG\GRQHVRPDNHDFRS\RI\RXUV\VWHPFRQILJXUD
WLRQLQIRUPDWLRQLQWKH6\VWHP6HWXSSURJUDP
If the settings are lost while you are replacing the battery, refer to your written or
printed copy of the system configuration information to restore the correct set-
tings. See Chapter 2, “Using the System Setup Program,” for instructions.
 5HPRYHWKHFRPSXWHUFRYHUDFFRUGLQJWRWKHLQVWUXFWLRQVLQ´5HPRYLQJ
WKH&RPSXWHU&RYHUµLQ&KDSWHU
&$87,21 6HH´3URWHFWLQJ$JDLQVW(OHFWURVWDWLF'LVFKDUJHµLQWKHVDIHW\
LQVWUXFWLRQVDWWKHIURQWRIWKLVJXLGH
 7RDFFHVVWKHEDWWHU\RQWKHV\VWHPERDUGUHPRYHWKHH[SDQVLRQFDUG
FDJHDVGHVFULEHGLQ´5HPRYLQJWKH([SDQVLRQ&DUG&DJHµLQ
&KDSWHU 
 /RFDWHWKHEDWWHU\DQGUHPRYHLW
The battery (see Figure 6-1) is mounted in a socket labeled “BATTERY,” in the
front-right corner of the system board (as you face the front of the system).
&$87,21 ,I\RXSU\WKHEDWWHU\RXWRILWVVRFNHWZLWKDEOXQWREMHFWEH
FDUHIXOQRWWRWRXFKWKHV\VWHPERDUGZLWKWKHREMHFW0DNHFHUWDLQWKDW
WKHREMHFWLVLQVHUWHGEHWZHHQWKHEDWWHU\DQGWKHVRFNHWEHIRUH
DWWHPSWLQJWRSU\RXWWKHEDWWHU\2WKHUZLVH\RXPD\GDPDJHWKHV\V
WHPERDUGE\SU\LQJRIIWKHVRFNHWRUE\EUHDNLQJFLUFXLWWUDFHVRQWKH
V\VWHPERDUG
Pry the battery out of its socket with your fingers or with a blunt, nonconductive
object, such as a plastic screwdriver.
 ,QVWDOOWKHQHZEDWWHU\
Orient the battery with the side labeled “+” facing up (see Figure 6-12). Then
insert the battery into the socket, and snap it into place.
:$51,1*
7KHUH LV D GDQJHU RI WKH QHZ EDWWHU\ H[SORGLQJ LI LW LV LQFRUUHFWO\
LQVWDOOHG5HSODFHWKHEDWWHU\RQO\ZLWKWKHVDPHRUHTXLYDOHQWW\SHUHF
RPPHQGHGE\WKHPDQXIDFWXUHU'LVFDUGXVHGEDWWHULHVDFFRUGLQJWRWKH
PDQXIDFWXUHU·VLQVWUXFWLRQV