Dell PowerEdge 6600 - Manual (Page 21)

SYSTEM
ID
SYSTEM NAME SYSTEM ID is a unique name, 5 characters or
less, defined by the user.
SYSTEM NAME is a unique name, 16 characters
or less, defined by the user.
The system ID and name display under the
following conditions:
l When the system is powered on
l When power is off and active POST
errors are displayed
This message is for information only.
You can change the system ID and name in the System Setup program. See
your system's User's Guide.
E0000 OVRFLW CHECK
LOG
LCD overflow message.
A maximum of three error messages can
display sequentially on the LCD. The fourth
message displays as the standard overflow
message.
Check the SEL for details on the events.
E0119 DRAC TEMP Remote access card is out of acceptable
temperature range. See " Troubleshooting System Cooling " in "Troubleshooting Your System."
E0119 TEMP AMBIENT Ambient system temperature is out of
acceptable range.
E0119 TEMP BP Backplane board is out of acceptable
temperature range. See " Troubleshooting System Cooling " in "Troubleshooting Your System."
Ensure that all power supply fans are operating properly. See " Troubleshooting
Power Supplies " in "Troubleshooting Your System."
E0119 TEMP CPU n Specified microprocessor is out of acceptable
temperature range. See " Troubleshooting System Cooling " in "Troubleshooting Your System." If the
problem persists, ensure that the specified microprocessor heat sink(s) are
properly installed (see "
Adding or Replacing a Microprocessor " in "Installing
System Options").
E0119 TEMP MEM n Specified memory riser card is out of acceptable
temperature range. See " Troubleshooting System Cooling " in "Troubleshooting Your System."
E0119 TEMP PBAY Peripheral bay is out of acceptable temperature
range. Ensure that all power supply fans are operating properly. See " Troubleshooting
Power Supplies " in "Troubleshooting Your System."
E0119 TEMP SYSTEM I/O riser card or I/O board is out of acceptable
temperature range. See " Troubleshooting System Cooling " in "Troubleshooting Your System."
E0212 DRAC EXT POWER Remote access card is out of acceptable
voltage range; faulty or improperly installed
power supply or remote access card. See " Troubleshooting Power Supplies " in "Troubleshooting Your System." If the
problem persists, ensure that the remote access card is properly installed. If
the problem persists, replace the remote access card (see "
Removing an
Expansion Card " in "Installing System Options").
E0212 DRAC VOLT BATT
E0212 DRAC VOLT PCI
E0212 VOLT 3.3 System power supply is out of acceptable
voltage range; faulty or improperly installed
power supply. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0212 VOLT 5
E0212 VOLT 12
E0212 VOLT BATT Faulty battery or I/O riser card. See " Troubleshooting the System Battery " and " Troubleshooting the I/O Riser
Card " in "Troubleshooting Your System."
E0212 VOLT BP 12 Backplane board is out of acceptable voltage
range. Ensure that the power cables are securely connected to the backplane board
(see "
Installing Drives "). If the problem persists, see " Troubleshooting Power
Supplies " in "Troubleshooting Your System." E0212 VOLT BP 3.3
E0212 VOLT BP 5
E0212 VOLT CPU VRM Microprocessor VRM voltage is out of
acceptable range; faulty or improperly installed
microprocessor VRM; faulty microprocessor
board. Ensure that supported VRMs of the same type are properly installed. If the
problem persists, replace the VRM (see "
Adding or Replacing a Microprocessor "
in "Installing System Options"). If the problem persists, replace the
microprocessor board (see "
Getting Help ").
E0212 VOLT NIC 1.8V Integrated NIC voltage is out of acceptable
range; faulty or improperly installed I/O riser
card; faulty or improperly installed power
supply. See " Troubleshooting the I/O Board " and " Troubleshooting Power Supplies " in
"Troubleshooting Your System."
E0212 VOLT NIC 2.5V
E0212 VOLT MEMORY n Specified memory riser card is out of acceptable
voltage range; faulty or improperly installed
memory card; faulty or improperly installed
power supply. Ensure that the memory riser card is properly installed. If the problem persists,
replace the memory riser card (see "
Removing the Memory Riser Cards " in
"Installing System Options"). If the problem persists, see " Troubleshooting
Power Supplies " in "Troubleshooting Your System."
E0212 VOLT PBAY 12 Peripheral bay is out of acceptable voltage
range. Ensure that the power cables are securely connected to the peripheral bay
backplane board (see "
Installing Drives "). If the problem persists, see
" Troubleshooting Power Supplies " in "Troubleshooting Your System." E0212 VOLT PBAY 3.3
E0212 VOLT PBAY 5
E0212 VOLT PLANAR
REG
Microprocessor board is out of acceptable
voltage range; faulty or improperly installed
microprocessor board. See " Troubleshooting the Microprocessor Board " in "Troubleshooting Your
System."
E0276 CPU VRM n Specified microprocessor VRM is faulty,
unsupported, or improperly installed. Ensure that supported VRMs of the same type are properly installed. If the
problem persists, replace the VRM (see "
Adding or Replacing a Microprocessor "
in "Installing System Options"). E0276 MISMATCH VRM n
E0280 MISSING VRM n Specified microprocessor VRM is improperly
installed or missing. Ensure that a supported VRM is properly installed for each microprocessor. If
the problem persists, replace the VRM (see "
Adding or Replacing a
Microprocessor " in "Installing System Options").
E0319 PCI OVER
CURRENT
Faulty or improperly installed expansion card or
I/O board. See " Troubleshooting the I/O Board " and " Troubleshooting Expansion Cards " in
"Troubleshooting Your System."
E0412 RPM FAN n Specified cooling fan is faulty, improperly
installed, or missing See " Troubleshooting a Cooling Fan " in "Troubleshooting Your System."