Dell PowerEdge 850 - Manual (Page 17)

or optical drive interface
cable, or loose power cable. " Troubleshooting an Optical Drive " in "Troubleshooting Your System."
Diskette read failure Faulty or improperly inserted
diskette. Replace the diskette.
Diskette subsystem reset failed Faulty diskette drive or
optical drive controller. Ensure that the diskette drive and optical drive cables are properly connected.
See "
Troubleshooting a Diskette Drive " and " Troubleshooting an Optical Drive "
in "Troubleshooting Your System." If the problem persists, see " Getting Help ."
Drive not ready Diskette missing or
improperly inserted in
diskette drive. Reinsert or replace the diskette.
Dual rank DIMMs are not supported in the
following memory sockets in this memory
configuration.
Invalid memory configuration. Correct the memory configuration. See " General Memory Module Installation
Guidelines " in "Installing System Components."
Error: Incorrect memory configuration.
Ensure memory in slots DIMM1_A and
DIMM1_B, DIMM2_A and DIMM2_B match
identically in size, speed, and rank.
An unmatched pair of memory
modules is installed. Install a matched pair of memory modules, or remove the memory module in
socket DIMM1_B. See "
General Memory Module Installation Guidelines " in
"Installing System Components."
Error: Remote Access Card initialization
failure.
Faulty or improperly installed
RAC. Ensure that the RAC is properly installed. See " Troubleshooting Expansion
Cards " in "Troubleshooting Your System," or " Installing a RAC Card " in
"Installing System Components."
Error 8602: Auxiliary device failure.
Verify that the keyboard and mouse are
securely attached to correct connectors.
Loose or improperly
connected mouse or
keyboard cable; faulty mouse
or keyboard. Replace the mouse. If the problem persists, replace the keyboard.
Gate A20 failure Faulty keyboard controller
(faulty system board). See " Getting Help ."
General failure Operating system corrupted
or improperly installed. Reinstall the operating system.
IDE Primary drive 1 not found Improperly connected or
missing optical drive or tape
backup unit. Ensure that the drive cables are properly connected. See " Troubleshooting
Your System " for the appropriate drive installed in your system.
If no drive is installed, disable the IDE controller. See "Using the System Setup
Program" in your User's Guide.
Keyboard controller failure Faulty keyboard controller
(faulty system board). See " Getting Help "
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Loose or improperly
connected keyboard cable;
faulty keyboard; faulty
keyboard controller. Ensure that the keyboard is properly connected. If the problem persists,
replace the keyboard. If the problem persists, see "
Getting Help ."
Keyboard fuse has failed. Keyboard fuse has failed. Replace the keyboard.
Faulty system board. See " Getting Help ."
Manufacturing mode detected System is incorrectly
configured. After the message appears during system boot, press <Alt><F> to turn off
manufacturing mode.
Memory address line failure at address,
read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at start
address to end address
Memory write/read failure at address,
read value expecting value
Faulty or improperly installed
memory modules, or faulty
system board. Ensure that all memory modules are properly installed. See " Troubleshooting
System Memory " in "Troubleshooting Your System." If the problem persists, see
" Getting Help ."
Memory tests terminated by keystroke The spacebar was pressed
during POST to terminate the
memory test. Information only.
No boot device available Faulty or missing diskette
drive, optical drive, or hard
drive. Check the Integrated Devices configuration settings in the System Setup
program. See "Using the System Setup Program" in your User's Guide. Ensure
that either SATA Controller, Diskette Controller, or IDE Controller is enabled.
If the system is booting from a SCSI controller, ensure that the controller is
properly connected. If the problem persists, replace the drive. See "
Installing
Drives ."
No boot sector on hard-disk drive An operating system is not
on the hard drive. Check the hard-drive configuration settings in the System Setup program. See
"Using the System Setup Program" in your User's Guide.
No timer tick interrupt Faulty system board. See " Getting Help ."
Not a boot diskette Not a bootable diskette. Use a bootable diskette.
PCI BIOS failed to install Loose cables to expansion
card(s); faulty or improperly
installed expansion card. Ensure that all appropriate cables are securely connected to the expansion
cards. See "
Troubleshooting Expansion Cards " in "Troubleshooting Your
System."
PCIe Degraded Link Width Error: Embedded
Bus#nn/Dev#nn/Funcn
Expected Link Width is n
Faulty or improperly installed
PCIe card. Reseat the PCIe cards. See " Expansion Cards ." If the problem persists, see
" Getting Help ."