Qmark CWH1000 Series - Small Room Fan-Forced Wall Heaters - Manual

WHB1000 Series
Fan Forced Wall Heaters
WHEN USING ELECTRIC APPLIANCES, BASIC
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND
INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1. Read all instructions before installing or using this heater.
2. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Keep combustible materials,
such as furniture, pillows, bedding, papers, clothes, etc. and
curtains at least 3 feet (0.9 m) from the front of the heater.
3. Extreme caution is necessary when any heater is used by or
near children or invalids and whenever the heater is left
operating and unattended.
4. Do not operate any heater after it malfunctions. Disconnect
power at service panel and have heater inspected by a
reputable electrician before using.
5. Do not use outdoors.
6. To disconnect heater, turn controls to off, and turn off power
to heater circuit at main disconnect panel.
7. Do not insert or allow foreign objects to enter any ventilation
or exhaust opening as this may cause an electric shock, fire,
or damage to the heater.
8. To prevent a possible fire, do not block air intake or exhaust
in any manner.
9. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids
are used or stored.
10. Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons.
11. This heater is provided with a red alarm light that will
illuminate only if the heater has turned off as a result of
overheating. If you see the light on, immediately turn the
heater off and inspect for any objects on or adjacent to the
heater that may have blocked the airflow or otherwise
caused high temperatures to have occurred. DO NOT
OPERATE THE HEATER WITH THE ALARM LIGHT
ILLUMINATING.
12. This heater is intended for comfort heating applications and
not intended for use in special environments. Do not use in
damp or wet locations such as marine or greenhouse or in
areas where corrosive or chemical agents are present.
13. When installing, see INSTALLATION INSTRUCTIONS for
additional warnings and precautions.
14. For safe and efficient operation, and to extend the life of
your heater, keep your heater clean - See MAINTENANCE
INSTRUCTIONS.
SAVE THESE INSTRUCTIONS
!
Installation, Operation & Maintenance Instructions
WARNING
IMPORTANT INSTRUCTIONS
PPD41511 09/14 5200-11213-000
Conforms to ANSI/UL2021 and CSA C22.2, No. 56
Conforms to ANSI/UL2021
and CSA C22.2, No. 56
Specifications
Accessories
Wire
Model Volts Amps Watts BTU/HR Size
WHB1101FC 120 8.4/4.2 1000/500 3413/1706 14AWG
WHB1151FC 120 12.5/6.3 1500/750 5120/2560 12AWG
WHB1201FC 120 15.0/7.5 1800/900 6143/3072 12AWG
WHB1202FC 240 8.4/4.2 2000/1000 6826/3413 14AWG
208 7.3/3.6 1500/750 5120/2560 14AWG
WHB1207FC 277 7.3/3.6 2000/1000 6826/3413 14AWG
240 6.3/3.2 1500/750 5120/2560 14AWG
WHB1157FC 277 5.5/2.75 1500/750 5120/2560 14AWG
240 4.7/2.4 1125/562 3840/1920 14AWG
WHB1208FC 208 9.6/4.8 2000/1000 6826/3413 14AWG
ASMW Surface Mounting Frame (Accessory) Order
Separately 12-1/2” (318mm)H X 10-3/8”
(264mm)W X 4” (102mm)
AS1W 1” (25mm) Recess Mounting Frame (Accessory)
Order Separately
AS2W 2” (50mm) Recess Mounting Frame (Accessory)
Order Separately
11” (279mm) 4” (102mm) 10-5/8” (270mm) 12-1/8” (307mm) 9-1/4” (235mm) 7/8” (22mm)
11”
(279mm)
4”
(102mm)
10-5/8”
(270mm)
12-1/8”
(307mm)
9-1/4”
(235mm)
7/8”
(22mm)