Document Outline

• Operating Manual PSENvip RL D M Set
• Preface
• Contents
• 1: Introduction
  • Validity of documentation
  • Overview of documentation
  • Definition of symbols
• 2: Overview
  • Range
• 3: Safety
  • Intended Use
    • Approvals
    • Safety during operation
      • Hazards arising from the installation of the PSENvip
      • Hazards when the press brake is in creep speed mode
      • Hazards arising from a reduced protected field
      • Hazards arising from incorrect handling of the workpiece
      • Correct handling of the workpiece
    • Categories / SIL
    • Tool shapes
    • Bending angle measurement
  • Standards
  • Safety guidelines
    • Use of qualified personnel
    • EMCD
    • Warranty and liability
    • Safety during commissioning, installation and operation
    • Disposal
• 4: Function Description
  • Overview
    • Bending angle measurement
  • Protected field
    • Standard press stroke
    • Standard interrupted press stroke
  • Overrun
  • Description of the units
    • Overview
    • Transmitter
      • Inputs
    • Receiver
      • Inputs
      • Outputs
      • LED
      • Key display and function
    • Communication with the safety system
  • Protected field modes
    • Standard protected field mode
    • Box bending protected field mode
    • Back gauge protected field mode
    • Box bending with back gauge protected field mode
  • Operating modes during commissioning
    • Press brake setup mode
    • Adjustment during initial commissioning
    • Adjustment during tool change
    • Setting the parameters for bending angle measurement
  • System cycle
    • System cycle for standard press stroke
    • System cycle for box bending press stroke
    • System cycle for back gauge press stroke
    • System cycle for box bending with back gauge press stroke
    • System cycle for overrun measurement
• 5: Installation
  • General requirements
  • Install transmitter and receiver
  • Dimensions
    • Transmitter
    • Receiver
    • Fastening kit for the transmitter
    • Fastening kit for the receiver
    • Bracket for transmitter and receiver
• 6: Wiring
  • Notes on wiring
  • Connections
    • Receiver
    • Transmitter
    • Supply voltage
    • Connection between transmitter and receiver
    • Connection diagram
• 7: Commissioning
  • Commissioning guidelines
  • Initial commissioning
    • Align transmitter and receiver
      • Prepare for alignment
      • Adjustment templates
      • Adjustment directions of transmitter and receiver
      • Align transmitter
      • Tool shapes
      • Align receiver
    • Adjustment template with bracket
  • Adjustment during tool change
    • Prepare for adjustment during tool change
    • Tool detection
    • Make adjustment during tool change
  • Enter overrun
  • Setting the parameters for bending angle measurement
  • Check protective equipment
    • Function test of the safety device
      • Test during initial commissioning
      • Test after machine modification
      • Regular check
      • Prepare for function test
      • Function test using the test piece
    • Visual inspection
• 8: Operation
  • Safety guidelines
  • Operating notes
    • Switch on PSENvip
    • Muting lamp
    • Initial press stroke
    • Measure bending angle
    • Acknowledge protected field modes
    • Tool change
    • Error messages
    • Cleaning the front lenses
• 9: Diagnostics and Troubleshooting
  • Troubleshooting
    • Minor errors
    • Major errors
    • Fatal errors
  • Error messages
  • DIAGNOSTICS menu
    • Diagnostic blocks and diagnostic data
• 10: System Connections
  • Overview
    • Communication with the safety system
    • Pin assignment
  • PSS
    • Application and parameters of individual blocks
  • PNOZmulti
    • Configuration of the inputs and outputs (e.g. PNOZ m1p)
    • Protected field mode
    • Evaluate OSSD
    • Overrun measurement
• 11: Technical Details
  • Technical Details
  • Order reference
• 12: Appendix
  • Checklist
  • EC declaration of conformity
• Contact address