OFNA Racing CD3 RTR - Manual (Page 36)

38406 AXLES, CVA DOG BONE PAIR (Captured Pin) 17.95
38407 DOG BONE, CVA PAIR 17.95
38408 MISC., LD3/CD3 CVA HARDWARE 5.95
38409 BEARING, THRUST, 4x9mm 15.95
38412 GEAR, STEEL BEVEL 40T, ONE-WAY ONLY 15.95
38413 CAP JOINTS, ONE-WAY 9.95
38414 GEAR, STEEL BEVEL AND OPINION, FOR DIFF CASE 23.95
38415 GEAR, STEEL BEVEL, SMALL 16T 7.95
38416 GEAR, STEEL BEVEL, LARGE 40T 15.95
38417 SWAYBAR, BLADE TYPE, FRONT AND REAR KIT 21.95
38418 BAR MOUNT, PLASTIC 1.95
38419 SHAFT, LONG, BLADE SWAYBAR KIT 7.95
38420 BAR, BLADE, SWAYBAR 2 PCS. 7.95
38422 ALUM. CNC CAP JOINT, CENTER/FRONT 13.95
38423 POWER CLUTCH, 30mm FLYWHEEL KIT 111.95
38424 ALUM. CNC FLYWHEEL, POWER CLUTCH, 30mm 19.95
38425 CLUTCH BELL, SCREW-ON, POWER CLUTCH 19.95
38426 SHOE, CLUTCH, BLACK 11.95
38427 SHOE, SLIDING, WHITE 11.95
38428 SPRING, POWER CLUTCH 3.95
38429 PILOT SHAFT, POWER CLUTCH 6.95
38430 COLLET, TAPER, POWER CLUTCH FLYWHEEL 3.95
38431 SPRING PLATE, POWER CLUTCH 3.95
38432 SPRING ADJUSTING NUT, POWER CLUTCH 5.95
38433 PLATE, CLUTCH SHOE, POWER CLUTCH 5.95
38434 SCREW, ADJUST, POWER CLUTCH 3.95
38435 ENGINE MOUNT, LOWER, NON-PULL START 31.95
38436 ALUM. CNC MOUNT, STEERING SERVO 11.95
38437 ALUM. CNC MOUNT, THROTTLE SERVO 11.95
38438 TUBE, SILICONE, PURPLE, LD3/CD3 MANIFOLD JOINT, SMALL 3.95
38439 BUMPER, TOP SUPPORT, GRAPHITE 21.95
38442 ALUM. CNC ARMS, UPPER AND SHOCK MOUNTS, 49.95
38443 ALUM. CNC ARM HOLDER, UPPER, 11.95
38444 TOWER, SHOCK, GRAPHITE 19.95
38445 HOLDER, ARM PIN, GRAPHITE 15.95
38446 ALUM. CNC HOLDER, FRONT AND REAR LOWER ARMS SET 23.95
38447 ALUM. CNC HOLDER, FRONT LOWER ARMS 11.95
38448 ALUM. CNC HOLDER, REAR LOWER ARMS 11.95
38449 PIVOT BALLS, STEEL, LOWER ARM HOLDERS 3.95
38451 ALUM. CNC DISC BRAKE HEAD, CENTER 9.95
38452 ALUM. CNC MOUNT, SWAYBAR 27.95
38453 ALUM. CNC SERVO SAVER UNIT 31.95
38454 ALUM. CNC SERVO SAVER TOP PLATE 7.95
38455 MOUNT, ALUM. CNC, SERVO SAVER LOWER 11.95
38456 ARM, ALUM. CNC, SERVO SAVER, NEW LONG TYPE 19.95
38457 PAD, BRAKE, BONDED CARBON&STEEL PAD 31.95
38458 ALUM. CNC GEAR 15T - GREEN, 1ST 9.95
38459 ALUM. CNC GEAR 16T - PINK, 1ST 9.95
38460 ALUM. CNC GEAR 17T - BLUE, 1ST 9.95
38461 ALUM. CNC GEAR 18T - GOLD, 1ST 9.95
38462 ALUM. CNC GEAR 19T - ORANGE, 1ST 9.95
38463 ALUM. CNC GEAR 19T - PURPLE, 2ND 9.95
38464 ALUM. CNC GEAR 20T - SILVER, 2ND 9.95
38465 ALUM. CNC GEAR 21T - LIGHT BLUE, 2ND 9.95
38466 ALUM. CNC GEAR 22T - GRAY, 2ND 9.95
38467 ALUM. CNC GEAR 23T - BLUE, 2ND 9.95
38468 ALUM. CNC GEAR 24T - RED, 2ND 9.95
38469 SPRING SET, FRONT/REAR, BLUE, YELLOW, & WHITE 13.95
38470 SPRING, SHOCKS, BLUE- SOFT 8.95
38471 SPRING, SHOCKS, YELLOW - MED. 7.95
38472 SPRING, SHOCKS, WHITE - HARD 7.95
38490 SNR RACING SPRING SET, LD3/CD3 6 PAIRS 23.95
38500 SNR CENTAX TOOL KIT 39.95
38501 SNR WRENCH PART, CENTAX TOOL KIT 27.95
38502 SNR JIG PARTS, CENTAX TOOL KIT 11.95
38505 SNR POCKET REAMER TOOL, HARD COATED 24.95
38506 SNR POCKET REAMER TOOL, BLACK 24.95
38507 SNR POCKET REAMER TOOL, POLISHED 24.95
38511 3x13.8 Pin for Shaft 5.95
38512 DECAL, CD3 LOGO 3.95
38513 1/10 Tire Inner Sponge 3.95
38514 1/10 Right Side Pipe 27.95
38515 1/10 Carry bag, 2 Case 59.95
38516 Brake Rod 3.95
38517 Radio Plate (plastic for CD3) 9.95
38518 Arm Stiffener & Battery Box for CD3 7.95
38519 Plastic Cap Joint for CD3 3.95
38520 Diff Housing for CD3 7.95
38521 Fuel Tank for CD3 11.95
38522 CVA Joint For Front / Rear 23.95