BendixKing KLN 900 - Pilots Guide - Manual (Page 91)

4-2 Rev 2
4.1.1 Creating A Flight Plan
A flight plan for a flight from Lakefront airport in New
Orleans, LA. to St. Petersburg/Clearwater, FL.
International airport will be used as an example of how to
create a flight plan. The waypoints making up the flight
plan are: KNEW (Lakefront airport), GPT (Gulfport VOR),
SJI (Semmes VOR), CEW (Crestview VOR), MAI
(Marianna VOR), TLH (Tallahassee VOR), CTY (Cross
City VOR), and KPIE (St. Petersburg/Clearwater
International airport. To create the flight plan:
1. Rotate the left outer knob to select the flight plan
(FPL) type pages (figure 4-1).
2. Turn the left inner knob to select a flight plan page
(preferably other than FPL 0) which does not contain
a flight plan (figure 4-2). If all of the flight plan pages
contain flight plans, refer to section 4.1.5, “Deleting
Flight Plans.”
3. Press the left C to turn on the cursor function for the
left page (figure 4-3).
NOTE: The KLN 900 flight plan operation is designed so
that the first waypoint in the flight plan should always be
the departure point. Remember to enter the “K”, “P”, or
“C” prefix for certain airports in the United States, Alaska,
or Canada. See section 2.3, “USE OF ICAO IDENTI-
FIERS.”
4. Use the left inner knob to select the first character of
the departure waypoint identifier (figure 4-4).
5. Turn the left outer knob one step clockwise to move
the flashing portion of the cursor over the second
character position, and then use the left inner knob to
select the desired character.
6. Use the above procedure to select the entire identifier
for the first waypoint (figure 4-5).
7. Press E . A waypoint confirmation page for the
identifier just entered will be displayed on the right
side (figure 4-6). If a mistake was made and the
wrong waypoint identifier was entered, press
F and
begin again. If a mistake was not made but the way-
point identifier just entered isn’t in the database, a
page allowing creation of a user defined waypoint will
appear on the right side. Refer to section 5.4, “USER-
DEFINED WAYPOINTS”, for instruction on how to
define a user created waypoint.
8. Press E again to approve the waypoint page being
displayed. The cursor will move to the second way-
point position (figure 4-7).
NOTE: A small number of waypoints are stored in the
database as “fly-over” waypoints. These waypoints are
associated with SID/STAR procedures. “Fly-over” means
USE? INVRT?|
1:KMKC |
2:BUM |
3:OSW |
4:TUL |
6:KRVS |
FPL 8
Figure 4-1
LOAD FPL 0?|
1: |
|
|
|
|
FPL 4
Figure 4-2
LOAD FPL 0?|
1: |
|
|
|
|
CRSR
Figure 4-3
LOAD INVRT?|
1:
K |
2: |
|
|
|
CRSR
Figure 4-4
LOAD INVRT?|
1:
KNEW |
2: |
|
|
|
CRSR
Figure 4-5
USE? INVRT?| KNEW
1:
KNEW |LAKEFRONT
2: |
| CL C
|N 30^02.53'
|W 90^01.69'
CRSR |enr-leg ent|APT 1
Figure 4-6
USE? INVRT?|
1:KNEW |
2: |
|
|
|
CRSR
Figure 4-7