Specification drawing, Dimensions, Water electric – Cleveland Range KGL-60-T User Manual
Page 7: Gas clearance
4
Specification Drawing -
Tilting, KGL-40-T, KGL-60-T, KGL-80-T
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Installation of backflow preventers, vacuum breakers and other specific codr requirements is the responsibility of the owner and installer.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are U.L., A.G.A., NSF, ASME/N.Bd., CSA, CGA, ETL and others.
1/2" dia. Soft
Copper
Tubing (each)
When ordered
with optional
faucet.
WATER
ELECTRIC
120V-1 Phase, 60 Hz, 10
amps
GAS
CLEARANCE
H
RIGHT = 0"
LEFT
= 0"
REAR = 3"
Allow 6" space minimum
from rear and sides when
located near combustible
walls. 12" recommended on
right side for service
NATURAL
PROPANE
Piping: 3/4" N.P.T.
Piping: 3/4" N.P.T.
Supply pressure:
Supply pressure:
4.00" W.C. minimum
4.00" W.C. minimum
14.00" W.C. maximum
14.00" W.C. maximum
Manufacturer must be notified if unit will be operated above 2,000 ft. altitude.
C
B.T.U. RATING
40 gal.
140,000
60 gal.
80 gal.
190,000
100 gal.
H C
DIMENSIONS
GALS./
LITERS
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
S I.D.
40
IN
45 3/4 42 1/2
38
35
9
42 1/4
71
40 1/2 15 1/2 23 1/4
19
35 3/4 4 3/8
24
33
63
26
150
mm
1163
108
966
889
229
1074
1804
1029
394
591
483
909
112
610
839
1601
661
60
IN
49 3/8
46
41 1/2
37
11 3/4 47 1/4
75
43 3/4 15 1/4 24 1/2
22
39 3/8
6
28
37
68
29 1/2
225
mm
1255
1169
1055
940
299
1201
1905
1112
388
623
559
1001
153
712
940
1728
750
80
IN
53
49
44 1/2
39
14 3/4
51
78
44 3/4
14
25
25
43
7
30
40
72
33
300
mm
1347
1245
1131
991
375
1296
1982
1137
356
635
635
1093
178
762
1016
1829
839
J
K
C
H
N
O
M
L
Q
P
3"
(77 mm)
REF
S I.D.
C
B
A
G
HANDWHEEL REPLACED
BY SWITCH FOR
POWER TILT OPTION
H
F
E
D
2 1/4"
(57 mm)
REF
2 1/2"
(64 mm)
2 1/2"
(64 mm)
4 1/8"
(105 mm)
3" (77 mm)
MIN.
CLEARANCE
UNIT SHOWN WITH OPTIONAL 2" TANGENT DRAW-OFF VALVE,
SPRING ASSIST COVER AND HOT & COLD WATER FAUCET.
9/16"
14 mm
120º
TYP
1" (25 mm)
MAX. ADJUSTMENT
1 5/8" (42 mm) Ø
FLANGED FOOT DETAIL
7/16" (11 mm) Ø
3 HOLES ON
3 1/8" (80 mm) Ø
B.C.D.
4 7/8"
124 Ø mm
RECOMMENDED
FLOOR SLOPE
1" (26 mm) per 4' (1220 mm)
PIPE DRAIN RECOMMENDED
min. valve size plus 1" (26 mm)
4" (102 mm)
RECOMMENDED
VALVE OPENING