Novak Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) - Manual (Page 2)

P6
throttle profile selection
m2 dig software flow chart
@NEUTRAL
BLUE-YELLOW-RED
LEDs on solid
DRAG BRAKE
BLUE & YELLOW
PROFILE
all LEDs (flashing)
DEAD BAND
BLUE & GREEN
MIN. DRIVE
YELLOW
press & hold SET button
continue holding ESC’
s SET button to skip steps here
LEDs roll off
ESC exits programming
# flashes = active profile
if pressed within 3 sec.
of all LEDs flashing
active profile changed
if not pressed within
3sec. of all LEDs flashing
VOLTAGE CUT-OFF
YELLOW-RED
DIG POWER
BLUE-GREEN-RED
DRIVE FREQ.
GREEN-RED
The M2 Dig 3S ESC features several
parameters that can be customized
to fine-tune the speed control’s feel
& response to your liking.
The flow chart below and the
adjustment steps to the right
describe the different parameters
and how they effect the ESC.
One-Touch Programming must be
completed before customization
o f p a r a m e t e r s , a s a l l E S C
parameters except Throttle Profile
are defaulted back to the factory
settings whenever the One-Touch
Programming is performed.
deFault SettiNGS FoR tHe
eSC PaRameteRS aRe liSted
iN Bold iN tHe taBleS to
tHe RiGHt
TO CHANGE PARAMETER SETTINGS:
1. CONNECT THE ESC TO A
RECEIVER AND A CHARGED
BATTERY PACK
2. SLIDE THE ESC’s ON/OFF
SWITCH TO ‘ON’ POSITION
3. WITH ESC AT NEUTRAL, PRESS
& HOLD SET BUTTON
release ESC’s SET button once LEDs
are lit for the desired setting.
To skip a parameter, continue
to press & hold SET button until
desired parameter is reached.
4. SELECT PARAMETER VALUE
LED flashes to indicate active setting
(refer to tables at right). Quick press
& release SET button to select
desired setting.
5. PRESS & HOLD SET BUTTON TO
STORE NEW SELECTION
When SET button is pressed and
held for about 1-2 seconds, the
new selection is stored in ESC’s
memory—Status LEDs will scroll across
to indicate ESC is exiting programming
& ESC returns to neutral.
There is no time constraint during
selection of custom parameters.
NEUTRAL
BLUE-YELLOW-RED
LEDs on solid
STATUS LED ORDER:
BLUE YELLOW GREEN RED
CUSTOM programmiNG options
The M2 Dig 3S Dual Brush speed control is equipped with 3 user-selectable
Throttle Profiles, as shown below:
• PROFILE 1 – Dig Mode – When the Aux/3rd switch/dial is thrown, the
dig function for either the front or rear motor (depending on the switch
position) will be engaged. The transmitter must have either a proportional
Aux switch or a simple three-position Aux switch.
• PROFILE 2 – Proportional Dig Mode – In this mode, the amount of dig
power applied to each motor is directly proportional to the position of the
Aux/3rd channel. The transmitter must have an Aux/3rd channel and
must have a proportional-style switch or control similar to a dial or knob.
• PROFILE 3 – Single Output Mode – This mode is used for standard two-
channel operation with either single or dual-motor control. There is no
dig function in this profile. A third channel is required for dig operation.
See STEP 1 for proper input harness connections and STEP 3 for proper
motor connections.
NOTE: The M2 Dig has the ability to run on either 2S or3S LiPo or LiFe
batteries via Novak’s auto detect software. When the appropriate voltage
cut-off circuitry is active (see programming on reverse side to turn ON/OFF),
the ESC automatically switches to the proper cut-off voltage for the battery
pack you connect.
m2 diG tHRottle PRoFileS
BruShED MOTOr PrOFILES
1 2 3
Dig
Proportional
Single Output
Dig (default)
Reverse 100% 100% 100%
Programmable yes yes yes
Drag/Hill Brake 40% 40% 40%
Dig Power 70% 70% N/A
Dead Band 5% 5% 5%
Minimum Drive 3% 3% 3%
Drive Frequency 2.5kHz 2.5kHz 2.5kHz
Voltage Cut-Off LiPo LiPo LiPo
NOTE: The M2 Dig is factory set to Profile #2
selecting throttle profiles: all LEDs
With ESC on & connected to a charged battery (transmitter ON or OFF):
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
To avoid possible radio interference, remove the ESC’s input signal
harness from the receiver-- green LED will stay on to indicate no signal
from receiver.
2. PRESS & HOLD THE ESC’S ONE-TOUCH SET BUTTON
Continue to hold SET button on ESC until all LEDs turn on.
Note: you will continue holding past all the LED programming
indicators in the speed control’s software as shown in the flow
chart on this sheet.
3. RELEASE SET BUTTON AS SOON AS ALL LEDs COME ON
Once released, the four status LEDs will flash to indicate what Throttle
Profile is currently selected. The number of times the LEDs flash indicates
the Brushless Throttle Profile selection (1 of 3).
4. QUICK PRESS (& release) SET BUTTON TO CHANGE SELECTION
Each press will change to the next consecutive Throttle Profile.
5. STORE SELECTION & EXIT TO NEUTRAL
Once the desired profile is selected, press and hold the SET button for 1-2
seconds. When the LEDs begin to scroll off, release the SET button and the
blue, yellow, & red LEDs will turn on solid. At this point, the ESC is at neutral
and ready to go.