Novak Brushless Motor: 55-5984-1.D__Manufacturing 6-Up Layout (55-5984-1.D) - Manual (Page 2)

INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
INSTALL THE NEW TIMING/SENSOR ASSEMBLY
1. Insert new timing assembly up into the bottom side of the end
bell or end ring with the sensor side toward the “inside” of the
motor and the sensor harness connector toward the outside.
2. Install the bearing cap onto the outside of the end bell/end ring
with the plastic sensor harness connector on the timing assembly
aligned with the sensor harness opening of the bearing cap.
3. Included with the new Timing/Sensor Assembly are new, shorter flat
head screws for the motor’s bearing cap. These screws must be used to
avoid possible shorting of the sensor assembly as the result of updates
made to the timing components. Insert the new M2.5 x 9mm flat-
head screws through the holes in the bearing cap and thread
them into the sensor assembly with a 1.5mm hex wrench.
4. Line up the timing notch on the end bell/ring with the proper
timing setting on the bearing cap’s timing label, then tighten
the three flat-head screws in a circular pattern to ensure that
the screws are tightened evenly--DO NOT OVER-TIGHTEN.
5. Place the fiberglass insulator under the back end bell/ring,
making certain that it is aligned correctly.
6. Line up the motor’s solder tabs with the opening in the back
end bell/ring, and slide the back assembly onto the motor,
guiding the rotor shaft into the bearing.
7. Once the back assembly is properly seated on the motor, use
a 3/32” hex wrench to tighten the three main screws on the
pinion shaft side of the motor into the back end bell/ring--use a
circular pattern, to ensure each screw is tightened evenly.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
Do not tighten the screws completely. Leave them a little loose
so that the end cap/timing assembly can swivel in the end bell.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.
PRODUCT WARRANTY Novak R/C, Inc. guarantees all products to be free from defects in materials or workmanship
for a period of 120 days from original date of purchase (verified by dated, itemized sales receipt). In no case shall our
liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.