Novak Mongoose Programming Sheet (55-3050P-1) - Manual (Page 2)

Setting (# of flashes): 1 2 3 4 5
Dead Band (%): 2 3 4 5 6
Setting (# of flashes): 1 2 3 4 5
Minimum Drive (%): 1 3 5 8 12
Setting (# of flashes): 1 2 3 4 5 6 7
Drive Frequency (kHz): 1.5 2.5 3.5 4.5 6.5 8.5 11
BLUE LED STAYS ON ALWAYS
Setting (# of flashes) : 1 2 3 4 5 6 7
Minimum Brake (%): 0 3 6 10 25 35 50
BLUE & AMBER LEDs ON ALWAYS
Setting (# of flashes) : 1 2 3 4 5 6 7
Drag Brake (%): off 3 6 10 25 35 50
to custom program profiles
:
Your transmitter can be either ON or OFF:
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
2. CONNECT SPEED CONTROL TO A CHARGED BATTERY PACK
3. SLIDE ESC’s ON/OFF SWITCH TO ‘ON’ POSITION
4. MAKE SURE THE THROTTLE PROFILE TO ADJUST IS ACTIVE
If you are not sure what profile is selected, follow the procedures in ‘Throttle Profile
Selection’ to check or select the desired profile.
5. FOLLOW STEPS ON RIGHT SIDE OF THIS PAGE TO CUSTOMIZE ESC
You can adjust different parameters (described on back side of this sheet) to fine tune the
speed control to perform & feel the way you like it.
Remember that you can not access the Brush-Mode (Profile #4) without
disconnecting the brushless motor’s sensor harness from the ESC.
Note: there is no time constraint during selection process of custom parameters.
mONGOOSE soFtware
Flow chart:
mongoose CUSTOM programmiNG
P6
to adjust minimum brake
:
(using this turns off drag brakes)
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE status LED turn on solid---Release
SET button once LED is on solid.
b. SELECT MINIMUM BRAKE PERCENTAGE blue LED
Blue status LEDs flash to indicate the Minimum Brake setting. Quick press & release the SET
button to change the Minimum Brake setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue LED also on if Min.Brake above 0%)---ESC is at neutral & ready to go.
to activate & adjust drag brake
:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE & AMBER status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. SELECT DRAG BRAKE PERCENTAGE blue & amber LEDs
Blue & Amber status LEDs flash to indicate the Drag Brake setting. Quick press & release the
SET button to change the Drag Brake setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs will also be on)---ESC is at neutral & ready to go.
to adjust dead band
:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the BLUE & GREEN status LEDs turn on
solid--Release SET button once LEDs are on solid.
b. SELECT DEAD BAND PERCENTAGE blue & green LEDs
Blue & Green status LEDs flash to indicate active Dead Band setting. Quick press & release SET
button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)---ESC is at neutral & ready to go.
to adjust minimum drive
:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until AMBER status LED turns on solid---Release
SET button once LED is on solid.
b. SELECT MINIMUM DRIVE PERCENTAGE amber LED
Amber status LED flashes to indicate active Minimum Drive setting. Quick press & release SET
button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
to adjust drive frequency
:
(Profile 4 ONLY)
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until GREEN status LED turns on solid---Release
SET button once LED is on solid.
b. SELECT DRIVE FREQUENCY green LED
Green status LED flashes to indicate active Drive Frequency setting. Quick press & release SET
button to change setting.
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
to activate liPO cut-off circuitry
:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the AMBER & RED status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. SELECT LiPo CUT-OFF CIRCUITRY SETTING amber & red LEDs
Amber & Red status LEDs flash to indicate LiPo Cut-Off setting. Quick press & release SET button to
change setting. 1 flash = OFF 2 flashes = ON/2-cell 3 flashes = ON/3-cell
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming. Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
to reverse motor rotation
:
a. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until AMBER & GREEN status LEDs turn on
solid---Release SET button once LEDs are on solid.
b. SELECT MOTOR ROTATION DIRECTION amber & green LEDs
Amber & Green status LEDs flash to indicate motor rotation direction. Quick press & release
SET button to change setting. 1 flash = Normal 2 flashes = Reverse
c. PRESS & HOLD SET BUTTON TO STORE SELECTION
Selection is stored in memory--Status LEDs scroll back & forth and ESC exits programming.Red
LED turns on solid (Blue & Amber LEDs may also be on)--ESC is at neutral & ready to go.
restoring factory defaults
:
Every time you perform the One-Touch Set-Up, the factory default settings
are restored for each of the throttle profiles & ESC reverts to Profile #1.
@NEUTRAL
RED LED on solid
MIN. BRAKE
BLUE
DRAG BRAKE
BLUE & AMBER
ACTIVE PROFILE
all LEDs (flashing)
DEAD BAND
BLUE & GREEN
MIN. DRIVE
AMBER
press & hold
press & hold
press & hold
press & hold
press & hold
continue
holding
ESC’
s SET
button
to
skip
steps
here
LEDs roll off
––––
exit programming
if Brush-Mode active
––––––
all LEDs
flash 4 times
@NEUTRAL
RED LED on solid
if Brushless-Mode active
––––––
# of flashes equals
active profile (1-3)
if pressed within 3 sec.
of all LEDs flashing
––––––
active profile changed
if not pressed
within 3 sec. of
all LEDs flashing
DRIVE FREQUENCY
GREEN
press & hold
if Brush-Mode active
if Brushless-Mode
is active
LiPo CUT-OFF
AMBER & RED
press & hold
MOTOR ROTATION
AMBER & GREEN
press & hold
if Brushless-Mode active
if Brush-Mode
is active