Rev-A-Shelf 4WCTM-1550DM-1 - Manual

INSTALLATION INSTRUCTIONS
for Top Mount Pull-Out Waste Containers
INSTRUCCIONES DE INSTALACIÓN
para cestos de basura deslizantes con montaje superior
NOTICE D’INSTALLATION
de la poubelle montée sur glissières supérieures
For models, Para los modelos, Pour les modèles:
4WCTM-12DM1, 4WCTM-15DM2, 4WCTM-18DM2
and 4WCTM-27-4
Step 2: Install front of slide to face frame. Hole is placed 3/8” from front of
cabinet. Bottom of slide should be 13 1/8” from cabinet floor. Use #8 x 5/8”
Low Profile Truss Head Screw.
Paso 2: Instale la parte delantera de la deslizadera en el bastidor
delantero. El orificio debe quedar a 9,5 mm (3/8 pulg.) del frente del armario.
La parte inferior de la deslizadera debe estar a 33,3 cm (13 1/8 pulg.) del piso
del armario. Use un tornillo de cabeza segmentada de perfil bajo núm.
8 x 5/8 pulg.
Étape 2: Monter l’avant de la glissière sur le cadre frontal. Le trou doit se
trouver à 9,5 mm (3/8 po) de l’avant de l’armoire. Le dessous de la glissière
doit se trouver à 33,3 cm (13 1/8 po) du fond de l’armoire. Utiliser une vis à
tête bombée à profil bas no 8 x 5/8 po.
Step 5: Mount Rear Bracket. Extend the slide rear mounting bracket until it
contacts the rear (Furring Strip). Bottom of slide should be 13/8” from cabinet
floor. Rear mounting bracket should be the same distance from the side
cabinet wall at rear of slide as it is up front. Drive mounting screw in center
horizontal slot of rear mounting bracket, tighten. Tighten screw in front
bracket.
Paso 5: Monte el soporte trasero. Extienda el soporte trasero de la
deslizadera hasta que toque atrás (el listón trasero). La parte inferior de
la deslizadera debe estar a 33,3 cm (13 1/8 pulg.) del piso del armario. La
distancia entre la parte posterior de la pared del armario a la deslizadera del
soporte de montaje trasero debe ser similar a la que tiene con respecto al
frente. Introduzca el tornillo de montaje en la ranura horizontal que está en
el centro del soporte de montaje trasero y apriételo. Apriete el tornillo en el
soporte delantero.
Étape 5: Monter le support arrière. Étendre le support de montage arrière
de la glissière jusqu’à ce qu’il touche l’arrière (le tasseau). Le dessous de la
glissière doit se trouver à 33,3 cm (13-1/8 po) du fond de l’armoire. La distance
séparant le
support de montage arrière de la paroi latérale de l’armoire doit être
identique à l’arrière et à l’avant. Placer une vis de montage dans la fente
horizontale du centre du support de montage arrière et la serrer. Serrer la
vis du support avant.
Step 6: Install wood unit (with slides attached) into cabinet, engaging
product member slides into cabinet member slides push unit until it locks
in place.
Paso 6: Instale la pieza de madera (con las deslizaderas instaladas) en
el armario de forma que las deslizaderas en el producto se entren en las
deslizaderas que están en el
armario y empuje hasta que cierren.
Étape 6: Installer l’ensemble en bois (avec les glissières
montées) dans l’armoire en engageant les glissières du produit dans celles
de l’armoire. Pousser sur l’ensemble jusqu’à ce qu’il s’enclenche.
Step 1: Install rear bracket to rear of slide.
Paso 1: Instale el soporte trasero en la parte posterior de la deslizadera.
Étape 1: Attacher le support arrière à l’arrière de la glissière.
INSTALLATION INSTRUCTIONS
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets
STEP 1:
Install front bracket to
front side of slide.
STEP 2:
Install rear bracket to
rear of slide.
For models: 4WCTM-12DM1, 4WCTM-15DM2 and 4WCTM-18DM2
STEP 3:
Mount slide to cabinet
if rear of cabinet is
thinner then 1/2" install
a 1/2" x 3" wide furring
strip to the back of the
cabinet centered
14 1/4" from floor of
cabinet.
STEP 4:
Measure from inside
cabinet wall to inside
face frame (A) distance
should be measured
the same at rear of
cabinet (B).
STEP 6:
Install wood unit (with slides attached) into cabinet,
engaging product member slides into cabinet member
slides, push
unit until it
locks in place.
Now you are
ready to
mount the
door.
STEP 7:
See door mounting instructions on inside.
14 1 / 4 "
13 1 /
2
"
STEP 5:
Position the slide with front
bracket on the face frame
opening and move it forward
until the self register stop hits the
inside of the face frame opening.
Bottom of slide should be 13 1/2"
from cabinet floor. Install screw in
slotted mounting hole, do not
tighten. Extend the slide rear mounting bracket until it
contacts the rear Furring strip. Bottom of slide should be
13 1/2" from cabinet floor. Rear mounting bracket should
be the same distance from the side cabinet wall at rear of
slide as it is up front. Drive mounting screw in center
horizontal slot of rear mounting bracket, tighten.
Tighten screw in front bracket.
Face Frame
Cabinet Member
Slides
Furring Strips
Furring
Strips
Product Member Cabinet Member
Self
Register
Stop
14 1 / 4 "
13 1 / 2 " 13 1 / 2 "
Front View
Top View
(A)
(B)
Step 3: If rear of cabinet is thinner then 1/2”, install a 1/2” x 3” wide furring
strip to the back of the cabinet centered 141/4” from floor of cabinet.
Paso 3: Si el grosor de la parte trasera del armario es inferior a
13 mm (1/2 pulg.), instale un listón de
13 x 76 mm (1/2 x 3 pulg.) de ancho
centrada en la parte trasera y a 36cm
(14 1/4 pulg.) del piso del armario.
Étape 3: Si l’arrière de l’armoire est
moins épais que 13 mm (1/2 po),
attacher un tasseau de
13mm x 76mm (1/2 x 3 po) à l’arrière
de l’armoire, centré à 36 cm (14-1/4
po) du fond de l’armoire.
Step 4: Measure from inside cabinet wall to inside face frame (A) distance
should be measured the same at rear of cabinet (B).
Paso 4: La medida de la pared interior del
INSTALLATION INSTRUCTIONS
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets
STEP 1:
Install front bracket to
front side of slide.
STEP 2:
Install rear bracket to
rear of slide.
For models: 4WCTM-12DM1, 4WCTM-15DM2 and 4WCTM-18DM2
STEP 3:
Mount slide to cabinet
if rear of cabinet is
thinner then 1/2" install
a 1/2" x 3" wide furring
strip to the back of the
cabinet centered
14 1/4" from floor of
cabinet.
STEP 4:
Measure from inside
cabinet wall to inside
face frame (A) distance
should be measured
the same at rear of
cabinet (B).
STEP 6:
Install wood unit (with slides attached) into cabinet,
engaging product member slides into cabinet member
slides, push
unit until it
locks in place.
Now you are
ready to
mount the
door.
STEP 7:
See door mounting instructions on inside.
14 1 / 4 "
13 1 / 2 "
STEP 5:
Position the slide with front
bracket on the face frame
opening and move it forward
until the self register stop hits the
inside of the face frame opening.
Bottom of slide should be 13 1/2"
from cabinet floor. Install screw in
slotted mounting hole, do not
tighten. Extend the slide rear mounting bracket until it
contacts the rear Furring strip. Bottom of slide should be
13 1/2" from cabinet floor. Rear mounting bracket should
be the same distance from the side cabinet wall at rear of
slide as it is up front. Drive mounting screw in center
horizontal slot of rear mounting bracket, tighten.
Tighten screw in front bracket.
Face Frame
Cabinet Member
Slides
Furring Strips
Furring
Strips
Product Member Cabinet Member
Self
Register
Stop
14 1 / 4 "
13 1 / 2 " 13 1 / 2 "
Front View
Top View
(A)
(B)
armario a la parte
interior del bastidor delantero
(A) debe ser similar en la parte
posterior del armario (B).
Étape 4: Mesurer à partir
de la paroi intérieure de
l’armoire jusqu’à l’intérieur du
cadre frontal (A). Mesurer la
même distance à l’arrière de
l’armoire (B).
Rear Mounting Bracket
presure fits over end of slide.
I-WCTM150SH-TRI-R
131/8” 131/8”
141/4”
Face Frame
123/4”
141/4”