Generac DUARDIAN 04077-2 - Manual (Page 8)

GENERAL
INFORMATION
Section 1 — G eneral Inform ation
Guardian Air-cooled 6 kW, 8 kW and 10 kW Generators
1.7 SPECIFICATIONS
♦ 1.7.1 GENERATOR
Model 04077 (6 kW) Model 04109 (8 kW) Model 04079 (10 kW)
Rated Maximum Continuous Power Capacity 6,000 Watts* 8,000 Watts* 10,000 Watts*
Rated Voltage 120/240 120/240 120/240
Rated Maximum Continuous Load Current
120 Volts 50 Amperes 66.7 Amperes 83.3 Amperes
240 Volts 25 Amperes 33.3 Amperes 41.6 Amperes
Phase 1 1 1
Number of Rotor Poles 2 2 2
Rated AC Frequency 60 Hz 60 Hz 60 Hz
Power Factor 1 1 1
Recommended Air Filter Generac Part #73111 Generac Part # 70941 Generac Part # 70941
Battery Requirement Group 26/26R
12 Volts and
350 Cold-cranking
Amperes Minimum
Group 26/26R
12 Volts and
350 Cold-cranking
Amperes Minimum
Group 26/26R
12 Volts and
350 Cold-cranking
Amperes Minimum
Weight 327 Pounds 357 Pounds 373 Pounds
•Miudmuin waltiige iuid current are subject to and limited by such factoi-s as fuel Btu content, ambient temperature, altitude, engine power and condition, etc. Maximuin power
decreases about 3.5 pereent for each 1,000 feet above sea level; and also will dettrease about 1 percent for each 12° C (10° F) above 15.5° C (60° F).
♦ 1.7.2 ENGINE
Model 04077 (6 kW) Model 04109 (8 kW) Model 04079 (10 kW)
IVpe ol Engine GN-410 GN-724 GN-724
Number of Cylinders 1 2 2
Rated Horsepower 14.5 @ 3,600 rpm 25 @ 3,600 rpm 25 @ 3,600 rpm
Displacement 410CC 724CC 724CC
Cylinder Block Aluminum w/Cast Aluminum w/Cast Aluminum w/Cast
Iron Sleeve Iron Sleeve Iron Sleeve
Valve Arrangement Overhead Valves Overhead Valves Overhead Valves
Ignition System Solid-state w/Magneto Solid-state w/Magneto Solid-state w/Magneto
Recommended Spark Plug RC12YC RC12YC RC12YC
Spark Plug Gap 0.76 mm (0.030 inch) 0.76 mm (0.030 inch) 0.76 mm (0.030 inch)
Compression-Ratio 8.6:1 8.6:1 8.6:1
Starter 12 Vdc 12 Vdc 12Vdc
Oil Capacity Including Filter Approx. 1.7 Qts Approx. 2.0 Qts Approx. 2.0 Qts
Recommended Oil Filter Generac Part #70185 Generac Part # 70185 Generac Part # 70185
1.8 RECONFIGURING THE
FUEL SYSTEM
To reconfigure the fuel system from NG to LP,
follow these steps:
1. Remove the carburetor fuel hose from the natu­
ral gas port of the fuel load block and the brass
fitting (Figure 1.3).
2. Remove the blanking plug from the LP port of
the load block (Figure 1.3).
Figure 1.3
-
Natural Gas Setup'
BRASS
Generac* Power Systems, Inc.