Chapter 10, Using the recover button – Dish Network DuoDVR ViP 722_TOC User Manual
Page 28
Chapter 10
82
The Recover Button
your satellite TV video. If RECOVER is programmed to a specific channel, RECOVER will tune the
TV to the specific channel first (for example, channel 60).
Programming the Recover Button for Remote Control 2
When your Remote Control 2 is shipped from the factory, RECOVER is set up to restore satellite
TV viewing by tuning your TV (or VCR) to channel 3, 4, and other inputs. To use RECOVER with
your remote TV (or VCR), you need to program RECOVER with the specific three-digit number
channel that you use to watch TV2 programming. (For two-digit number channels, use zero first.
For example, enter channel 60 as 060.) The following instructions describe how to program
RECOVER to tune your remote TV (or VCR) back to a selected channel.
Using the Recover Button
The following setup is required to use RECOVER:
•
The remote control must be set up to control the TV and, if installed, the VCR.
•
If a VCR is installed, it must be connected as shown on page 109.
•
On a remote TV, RECOVER must be programmed to tune your remote TV to the specific
channel to receive TV2 programming (for example, channel 60), using the instructions on
page 82.
Note: Press any remote control button other than RECOVER to end this procedure.
Note: If RECOVER is not programmed to a specific channel, RECOVER will first try to tune your
TV to channel 3, then channel 4, and then other video inputs with each press of RECOVER. You
may need to press RECOVER up to 30 times to recover your satellite TV video. If RECOVER is
programmed to a specific channel (see page 82), RECOVER will tune the TV to the specific
channel (for example, channel 60).
1
2
3
5
4
Press and hold the
TV Mode button until all
Mode buttons light up
(button will flash)
Program Remote 2 to
control your remote
TV
Press
STAR
TV
Enter the
digits of your
channel number
Press POUND
(TV Mode button
will flash 3 times)
6
5
4
3
2
1
9
8
7
#
0
R
DVR
SELECT
POWER
TV
SAT
VCR
AUX
TV
TV/VIDEO
VOLUME
MENU
PAGE
MUTE
GUIDE
RECALL
CANCEL
INFO
VIEW TV
SKIP
BACK
BACK
SKIP
FWD
FWD
PAUSE
STOP
PLAY
RECORD
PIP
search
/format
abc
def
ghi
mno
jkl
pqrs
wxyz
tuv
T
H
E
M
E
S
B
R
O
W
S
E
P
A
W
S
P O SI
T
IO
N
I
N
P U
T
1
1
2
3
4
5
Press
and hold
RECOVER
until all
Mode buttons
light up
Press RECOVER
again and wait for the
TV or VCR Mode
buttons to flash once
then all four Mode
buttons to flash once
SELECT
When the System
Information screen
displays, you have
recovered your satellite
programming
(press SELECT to exit)
Don’t see the System
Information Screen?
Repeat steps 2 & 3
until the System Information
screen appears
Make sure
your TV is
on
2
Next
System Info
Mon, October 18
Copyright 2005, EchoStar Technologies Corp. All Rights Reserved.
Details
Done
a
d
e
g
h
c
b
f
i
j
St
atus: Good
0
0
DISH Pl
ayer-DVR 522
Softw
are: L236
R00 0000 0000-01
S00 0000 0000-01
S
atellite:
Sign
al:
119
110
148
De
vice: DP34, Feed(1), Feed(2), Feed(3)
Re
mote Addrs.
TV Out
UHF
3
5
Re
mote Addrs.
TV Out
UHF
3
5
1
2