DR Power Tow-Behind 13.74 Pro-XL (August 2010 - August 2014) - Manual (Page 9)

CONTACT US AT www.DRpower.com 9
Specifications
PREMIER PRO PRO-XL
Engine Refer to the Engine Operator Manual for Engine Specifications
Impeller Welded Steel Welded Steel Welded Steel
RPM 3400 3400 3400
Chipper Knife None D2 Tool Steel, Hardened 52-56 RC D2 Tool Steel, Hardened 52-56 RC
Chipper Knife Size None 4.12" x 1.25" x .25" 4.12" x 1.25" x .25"
Weight 16.2 LBS 16.8 LBS 16.8 LBS
Chipping Capacity None 2" Diameter Branches 2" Diameter Branches
Vacuum 1562 CFM 1562 CFM 1562 CFM
Suction 90 MPH 90 MPH 90 MPH
Impeller Drive Direct Thru Sure-Flex Coupling Direct Thru Sure-Flex Coupling Direct Thru Sure-Flex Coupling
Collector Hardshell on Steel Base Frame Hardshell on Steel Base Frame Hardshell on Steel Base Frame
Volume 245 Gallons 306 Gallons 306 Gallons
Capacity 300 LBS 500 LBS 500 LBS
Base Frame Welded Steel Tubing (1" Sq x .06") Welded Steel Tubing (1" Sq x .06") Welded Steel Tubing (1" Sq x .06")
Dump Tilt 50° 50° 50°
Frame Welded Steel Welded Steel Welded Steel
Tubular Structure 1.25" Round & SQ Tubing x .12" 1.25" Round & SQ Tubing x .12" 1.25" Round & SQ Tubing x .12"
Impeller Housing 3 Piece Design 3 Piece Design Plus Hopper 3 Piece Design Plus Hopper
Wheels Tubeless Pneumatic 4.10/3.50-5 Tubeless Pneumatic 4.10/3.50-5 Tubeless Pneumatic 4.10/3.50-5
Hitch Single Point Single Point Single Point
Jack Optional (Customer Install) Unique frame mount. (Installed) Unique frame mount. (Installed)
Lawn Mower Discharge Right or Left Right or Left Right or Left
Dimensions 90" L x 47.62" W x 57.5" H 90" L x 47.62" W x 65.75" H 90" L x 47.62" W x 65.75" H
Weight 310 Lbs 325 Lbs 332 Lbs
Shipping Dimensions 77.5" L x 49" W x 41" H 77.5" L x 49" W x 41" H 77.5" L x 49" W x 41" H
Shipping Weight 398 Lbs 413 Lbs 420 Lbs
Unpacking and Assembling the Machine
NOTE: Unpacking the DR Leaf and Lawn Vacuum is a two-person job. We
recommend you have an extra set of hands available before you begin
because the DR Leaf and Lawn Vacuums weigh 310 lbs. (Premier), 325 lbs.
(Pro) and 332 lbs. (Pro-XL).
Unpacking the Shipping Box
Tools and Supplies Needed:

Gloves
 Eye Protection

Wire Cutters
1. Stand to one side and cut the banding.
2. Remove the top of the Box.
3. Lift the Top Cover from the Shipping Container and set aside (Figure 2).
4. Pull open the Box Seams on both sides of the stapled carton and pull the
bottom away from the Pallet as you fold the ends down (Figure 3). The
staples are sharp so be careful.
 Stabilize the shipping box on flat terrain before attempting to unpack and
assemble the machine.

Wear eye protection when cutting the Wire Ties and bands. The banding
may have a lot of tension on it and may snap and cut you. Always stand to
one side when cutting the bands.
Top Cover
Figure 2
Box
Seams
Figure 3
Staples Inside
Box Lip
Staples on Bottom