La Crosse Technology K2-100 - Manual (Page 5)

GB
GB GB
GB
Altimeter Graph Display
13
4.8 Time Keeping Mode - Setting the UPV for the Timer and the Timer Counting Display
UPV and Timer Counting Display Setting Sequence
Timer Display
digits have been
selected (flashing)
User Pre-set Value (UPV)
Setting Display
C (Celsius)
m (Meter)
C (Celsius)
ft (Feet)
F(Fahrenheit)
ft (Feet)
F (Fahrenheit)
m (Meter)
hold
lap/reset
hold
lap/reset
hold
lap/reset
hold
lap/reset
Unit Selection Sequence
Graph Scale Display
24 Hour Memory Display
Altitude Setting Sequence
To view the memory
by forward scrolling
(from -24 hour to -15 min.
To view the memory
by backward scrolling
(from -15 min. to -24 hour)
To Set the UPV and the Timer Counting DIsplay
- Press and hold the [adjust] button for 2 seconds to
change the display from Timer Display to User Pre-set
Value Setting Display.
- T h e h o u r d i g i t s f l a s h o n t h e d i s p l a y b e c a u s e i t i s
being selected.
The setting procedure
- Press [adjust] button to change the selection as in the
User Pre-set Value Setting Sequence.
- While digits are being selected (flashing), press the
[start/stop] button to increase the number; press the
[lap/reset] button to decrease the number. Hold down the
button to change the number at a higher speed.
- W h e n t h e F L A S H I N G P A R T m o v e s t o " R E P E A T " o r
"COUNT " character, just press [start/stop] or [lap/
resst] button to select the Countdown timer or Repeater
timer.
- After you set the timer, press the [mode] button to exit
the setting sequence.
- If no button is pressed in the setting display for about 3
m i n u t e s , t h e K 2 - 1 0 0 w i l l r e t u r n t o t h e T i m e r M o d e
automatically
hour second minute
Timer Counting Display
(Countdown Timer or
Repeater Timer)
adjust adjust
adjust adjust
14
To Use the Timer
- When the Timer is set, press the [start/stop] button to
start the timer. Press the [start/stop] button again to stop
the timer.
- The time to 'Zero' will be shown on the display.
-
The timer starts to beep every second when it is 5
seconds from the end of the countdown.
- When the countdown time is reached, a long beep that
lasts for 2 seconds will be heard.
- Pressing any button in this period will terminate the beep
sound prematurely.
- The user preset time will be loaded automatically at the
end of the beep sound.
To Reset the Timer
- Press and hold the [lap/reset] button for 2 seconds to
reset the timer after it has stopped.
4.9 Time Keeping Mode - Using the Timer
Timer Display
(Timer sets as 1 minute)
Counting Display
Stop Counting Display
Counting Display
digits start
counting
digits stop
counting
digits start
counting
again
start/stop
start/stop
start/stop
hold
lap/reset
16
5.0 Altimeter Mode and its sub-displays
5.0 Altimeter Mode and its sub-displays ... continue
15
Altimeter Graph Display
adjust
button
hold
lap/reset
mode
button
hold
adjust
lap/reset
button
adjust
button
adjust
button
adjust
button
adjust
button
adjust
button
mode
button
start/stop
lap/reset
m
P
mode
button
mode
button
hold
adjust
hold
adjust
12
13
14
15
60
15
30
45
m
P
60
15
30
45