Document Outline

• TempScan / MultiScan User's Manual
• Warranty
• Warnings, Cautions, Notes & Tips
• Manual Layout
• Table of Contents
• TempScan / MultiScan Quick Start Guide (p/n 446-0940)
  • Hardware Setup
  • Software Setup & Startup
• Ch 1 - System Overview
  • Introduction
    • TempScan/1100
    • MultiScan/1200
    • Front Panel Indicators
    • Rear Panel Switches & Connectors
    • TempScan/1100 & MultiScan/1200 Specifications
  • Hardware Configuration
    • IEEE 488 Configuration
    • RS-232/422 Serial Configuration
    • Calibration Protection Configuration
    • Digital I/O Configuration
    • TTL Output & Trigger Input Configuration
    • Expanded Memory Configuration
    • Scanning Card & Channel Expansion
  • Power Line & Fuse Configuration
    • Introduction
    • Line Voltage Selection
    • Fuse Replacement
  • Rack-Mount & Bench-Top Assembly
    • Rack Mount
    • Bench Top
  • Power-Up Activation
• Ch 2 - Expansion Units
  • Exp/10A Expansion Unit
    • Introduction
    • Front Panel Indicators
    • Rear Panel Switches & Connectors
    • Exp/10A Specifications
  • Exp/10A Hardware Configuration
    • Master/Slave Connection
    • Slave Configuration
    • Channel Assignment
  • Exp/11A Expansion Unit
    • Introduction
    • Front Panel Indicators
    • Rear Panel Switches & Connectors
    • Exp/11A Specifications
  • Exp/11A Hardware Configuration
    • Master/Slave Connection
    • Slave Configuration
    • Channel Assignment
• Ch 3 - Scanning Cards
  • TempScan Scanning Cards
    • TempTC/32B Thermocouple Scanning Card
    • TempV/32B Voltage Scanning Card
    • TempRTD/16B RTD Scanning Card
  • MultiScan Scanning Cards
    • MTC/24 Thermocouple/Volt Scanning Card
    • MHV/24 High-Voltage Scanning Card
• Ch 4 - System Configuration
  • Introduction
  • Memory Allocation
  • Measuring Modes (MultiScan/1200 Only)
    • Line-Cycle Integration / High-Speed Multi-Channel Mode
    • Single-Channel High-Speed Burst Mode
  • Required Configuration
    • Channel Configuration
    • Scan Configuration
    • Acquisition Configuration
    • Trigger Configuration
  • Additional Configuration
    • Alarm Configuration
    • Stamp Configuration
    • Data Format Configuration
    • Power-Up Configuration
• Ch 5 - System Operation
  • Acquisition Buffer
    • Buffer Organization
    • Buffer Query Operation
    • Buffer Read Operations
    • Buffer Overrun
  • High/Low/Last (HLL) Registers
    • Contents of the HLL Registers
    • Access to the HLL Registers
    • Comparing Buffered Data to HLL Data
  • Status-Reporting & Mask Registers
    • Theory of Operation
    • Status-Reporting Registers
    • Mask Registers
    • Using Status-Reporting Registers
  • Additional Operation
    • Trigger Latency
    • Real-Time Clock
    • Open Thermocouple & Range Error Checking
    • Software Digital Filtering (TempScan/1100 Only)
• Ch 6 - System Calibration
  • Introduction
  • Calibration Setup
    • Calibration Properties
    • Calibration Protection
    • Calibration Status
    • Calibration Password
  • Calibration of Master Chassis
  • Calibration of Scanning Cards
    • Calibration of Thermocouple Scanning Cards
    • Calibration of Voltage Scanning Cards
    • Calibration of RTD Scanning Cards
• Software
  • ChartView Software Reference
    • Overview
    • Main Window
    • Main Window Toolbar
    • Main Window Pull-Down Menus
    • Bar Graph, Analog, and Digital Meters
    • Setup Window
    • Chart Setup Wizard
  • ViewXL
    • Overview
    • Menu
    • Toolbar
    • Using the ViewXL Program API
    • An Example Macro
    • ViewXL API Definition
• APPENDICES
  • Appendix A - API Command Reference
    • Introduction
      • Command Syntax
      • Command Interpretation
      • Command Summary
    • Command Reference
      • Command Description Format
      • The Commands
  • Appendix B – IEEE 488, Serial, and ASCII B
    • IEEE 488 Bus & Serial Bus Lines
    • …… A-IEEE 488 Bus Commands
    • …… A-ASCII Codes
    • Abbreviations
  • Appendix C – Program Examples in Quick Basic C
    • Introduction
    • Reading HLL Status
      • TempScan/1100
      • MultiScan/1200
    • Reading HLL Data from Thermocouple & Volts Cards
      • TempScan/1100
      • MultiScan/1200
    • Acquiring Pre- & Post-Trigger Data at Different Rates
      • TempScan/1100
      • MultiScan/1200
    • Acquiring Pre- & Post-Trigger Data at the Same Rate
      • TempScan/1100
      • MultiScan/1200
    • Operating Alarms
      • TempScan/1100
      • MultiScan/1200
    • Using the IEEE 488 SRQ with Alarms
      • TempScan/1100
      • MultiScan/1200
    • Acquiring Buffer Data in Binary Format
      • TempScan/1100
      • MultiScan/1200
    • Acquiring HLL Data in Binary Format
      • TempScan/1100
      • MultiScan/1200
    • Using Auto Re-arm to Capture Multiple Trigger Blocks
      • TempScan/1100
      • MultiScan/1200
    • Acquiring Burst Mode Data (MultiScan/1200 Only)