Thinklogical X4 and Touchpanels - Manual (Page 6)

®
V e l o c i t y D V I E x t e n d e r P r o d u c t M a n u a l , R e v . H , D e c . 2 0 1 4 Page 4
1. Introduction
1.1. Contents
Upon receiving your Thinklogical VelocityDVI Extension System ® you should find the following
items:

DVI Extender Transmitter

DVI Extender Receiver

DVI-D Male to Male Cable, 2 Meter (CBL-000009-002MR) 1

DVI-D Male to Male Dual-Link Cable, 2 Meters (CBL-000023-002MR) 2

Universal AC Power Adapters (PWR-000022-R) – Quantity 2 (Vel-3, -6)

AC Power Cord (PWR-000006-R) – Quantity 2 (Vel-33, -63)

CAT5 Cable Assembly (CBL000001-002MR) 3

3.5mm Audio Cable, M-M – Quantity 2 (CBL000016-006FR) 3

DB9F Adapter (ADP-000025-R) and DB9M Adapter (ADP-000019-R) 4

CD Product Manual
1 For VelocityDVI-3, Qty = 1 each. For VelocityDVI-33, Qty = 3 each
2 For VelocityDVI-6, Qty = 1 each. For VelocityDVI-63, Qty = 3 each
3 With A/V+ and A/N+ models
4 With A/V+ models only
1.2. Product Overview
MRTS Technology 6.25 Gbps. allows for Full Frame Rate Transmission of uncompressed DVI.
Powered by Thinklogical’s
® cutting edge, patent-pending MRTS (Multi Rate Transmission System)
Technology, our DVI Extension Systems transport every frame of a DVI video stream seamlessly with no
compression or dropped frames. In addition, all high speed peripherals function with no latency.
Incorporating standard SFP+ transceivers, the system uses multi-mode fiber optic cable to permit the
placement of a digital monitor or projector up to 1000 meters (3280 feet) away from the controlling
computer without loss of resolution. Thinklogical
® also offers optics that use single-mode fiber optic
cables to allow the placement of video devices up to 10, 40 or 80 km (6.2/24.8/49.7 miles) away from
the controlling computer without loss of resolution. Installation is plug-and-play and no adjustments
are necessary.
Each VEL-3 (single-link) and VEL-6 (dual-link) system consists of one transmitter per chassis
and one receiver per chassis. The rack-mountable VEL-33 system (single-link) and the rack-
mountable VEL-63 system (dual-link) each feature three transmitters per chassis and three
receivers per chassis. All models support Data Display Channel (DDC), with a variety of modes to
meet each unique requirement. All models are connected by fiber optic cable(s), the count of which
varies depending upon the DDC mode to provide communications to and from the transmitter. The
transmitter unit connects to the CPU with supplied DVI-D cables (and audio, serial & network cables
in A/V+ and A/N+ models). The receiver unit provides an interface to the monitor(s) (and audio, serial
& network devices in A/V+ and A/N+ models).
Each Transmitter (TX) features a video input and local video output which can be used for DDC
modification and for displaying video at the source. The TX also has fiber connectors used for
transferring video and data to the Receiver. (For an Automatic Fail-Over option, see Appendix D,
on page 47 for more details.) Status LEDS and DDC Mode buttons are provided for system
configuration.
Each Receiver (RX) features two video outputs. DVI to Display DDC is the primary output and DVI to
Display is an auxiliary output. The RX has fiber connectors used for transferring data to the TX and
for receiving video and data from the TX. Status LEDS and DDC Mode buttons are provided for
system configuration.