Kichler 43680 - Manual

MOUNTING STRAP
ABRAZADERA DE MONTAJE
1) Pass wire from fixture through stem and screw stem to
coupling on top of fixture body.
NOTE: Thread locking compound must be applied to all
stem threads as noted with symbol (3) to prevent accidental
rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) If using swivel for sloped ceilings, pass fixture wire through
swivel and thread swivel onto top of last stem.
NOTE DIRECTION OF SWIVEL IN ACCORDANCE WITH
CEILING.
4) Pass fixture wire through small threaded pipe. Thread small
threaded pipe into end of swivel.
5) Pass fixture wire through hole in canopy. Pass threaded pipe
on end of swivel up through hole in canopy.
6) Pass fixture wire through hole in lockwasher. Thread lockwasher
over end of threaded pipe protruding from inside canopy.
7) Pass fixture wire through hole in hexnut. Screw hexnut onto
threaded pipe.
8) If not using swivel, pass threaded pipe through small
threaded pipe. Thread small threaded pipe into end of last
stem.
9) Pass fixture wire through hole in canopy. Pass threaded pipe
on end of stem up through hole in canopy.
10) Pass fixture wire through hole in lockwasher. Thread lockwasher
over end of threaded pipe protruding from inside canopy.
11) Pass fixture wire through hole in hexnut. Screw hexnut onto
threaded pipe.
12) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
13) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
14) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
15) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 10/24/14 IS-43680-US
CANOPY
ESCUDETE
STEM
VÁSTAGO
KNURL KNOB
PERILLA ESTRADA
SWIVEL
UNIÓN GIRATORIA
3
3
SHADE
PANTALLA
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
16) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
17) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
18) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
19) Raise shade up to fixture. Pass hole in shade over socket.
20) Thread socket ring onto socket. Tighten socket ring to
secure shade in place. (DO NOT over tighten.)
21) The angle of the two arms is adjustable and the angle of the
two lights on either end of the arms is adjustable.
NOTE: The position of the center light is not adjustable
To adjust the angle of the arms: Loosen each wing nut
located on the hub in the center of the fixture. Carefully
move arms to desired position. The teeth on the hub should
fit within the space of each other. Carefully tighten wing nuts
to secure the position of the arms.
To adjust the angle of each light: Loosen the wing nut at
end of arm. Carefully move the light to the desired position.
Carefully tighten wing nut.
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
SOCKET RING
ANILLO DEL CASQUILLO
LOCKWASHER
ARANDELA DE SEGURIDAD
HEXNUT
TUERCA HEXAGONAL
WING NUT
TUERCA DE
MARIPOSA UBICADA
WING NUT
TUERCA DE
MARIPOSA UBICADA