Epson 25 - Manual (Page 64)

64
exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
• Do not expose this unit to water or place objects con-
taining liquids on this unit.
• Do not place the source of a naked flame, such as a lit
candle, on this unit.
• Connect this unit to an earthed electrical outlet.
• Ensure there is at least 8 inches between the exhaust
vent and any walls, etc.
• Ensure there is at least 4 inches between the air
intake vent and any walls, etc.
• Do not project when the lens cover is on.
It is possible that the lens cover may melt from the
heat and cause burns or injuries.
To interrupt the projection, press [Video On/Off] dur-
ing projection.
• Do not leave this unit or the remote control with its
batteries installed in such places as the inside of a car
with the windows closed, in direct sunlight, near the
intake/exhaust of an air conditioner or heater, or in
places where the temperature rises above normal.
This may have a negative effect upon the internal
parts of this unit and cause heat deformation or fire.
• When unplugging the power plug/power connector,
do not pull on the power cable.
Make sure you grasp the plug or connector part, then
unplug.
• Do not set the volume too high from the outset.
A loud sound may be produced suddenly that may
cause damage to the speaker or your hearing. As a
precaution, lower the volume before you switch off
this unit then raise it gradually after you switch it
back on.
• When using headphones, do not turn the volume up
too loudly.
You may adversely affect your hearing when listen-
ing at loud volumes over extended periods of time.
• When maintaining this unit, remove the power plug/
power connector form the wall outlet.
If not, you run the risk of an electric shock.
• Do not place the projector on an unstable cart, stand,
or table.
• Use the type of power source indicated on the projec-
tor. If you are not sure of the power available, consult
your dealer or local electricity company.
• Place the projector near a wall outlet where the plug
can be easily unplugged.
• Check the specifications of the power cable. Using
an inappropriate power cable could result in fire or
electric shock.
The power cable supplied with the projector is
intended to comply with power supply requirements
for the country of purchase.
If using the projector overseas, check the power sup-
ply voltage and outlet shape that conform to the local
standards, and purchase a proper power cable in the
country.
• Take the following precautions when handling the
plug. Failure to comply with these precautions could
result in fire or electric shock.
− Do not insert the plug into an outlet with dust
present.
− Insert the plug firmly into the outlet.
− Do not handle the plug with wet hands.
• Do not overload wall outlets, extension cables, or
integral convenience receptacles. This can cause fire
or electric shock.
• Do not place the projector where the cable can be
stepped on. It may result in fraying or damage to the
plug.
• Unplug the projector from the wall outlet before
cleaning. Use a damp cloth for cleaning. Do not use
liquid or aerosol cleaners.
• Do not block the slots and openings in the projector
case. They provide ventilation and prevent the pro-
jector from overheating. Do not place the projector
on a sofa, rug, or other soft surface, or in a closed-in
cabinet unless proper ventilation is provided.
• Never push objects of any kind through cabinet slots.
Never spill liquid of any kind into the projector.
• Unplug the projector from the wall outlet and refer
servicing to qualified service personnel under the fol-
lowing conditions:
− When the power cable or plug is damaged or
frayed.
− If liquid has been spilled into the projector, or it
has been exposed to rain, water, or excessive
humidity.
− If it does not operate normally when you follow the
operating instructions, or if it exhibits a distinct
change in performance, indicating a need for
service.
− If it has been dropped or the housing has been
damaged.
• The internal projector components consist of many
glass parts such as the lens and projection lamp.
The lamp is fragile, and can easily break. If the lamp
breaks, handle the projector with extreme care to
avoid injury from broken glass, and contact Epson
for a replacement.