PLANET POE-161 - Manual (Page 2)

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Note
The POE-161 and POE-162S can be installed
in pair. However, the use of third-party device
is allowed if the device complied with IEEE
802.3at Power over Ethernet.
POE-161, the Injector Installation
1. Connect the AC adapter to “DC 56V” of POE-161. The
power LED will be steady on.
2. Connect a standard network cable from Switch/worksta-
tion to “Ethernet” port of POE-161.
3. Connect the long cable that will be used to connect to
the remote device to the port “Ethernet + DC”.
4. Connect with IEEE 802.3at devices, due to the capability
of IEEE 802.3at Power over Ethernet, the POE-161 can
directly connect with any IEEE 802.3at end-nodes such
as PTZ (Pan, Tilt & Zoom) network cameras, PTZ Speed
Dome, color touch- screen Voice over IP (VoIP) tele-
phones, multi- channel wireless LAN access points where
support IEEE 802.3af In-line Power over Ethernet port.
The screen in Figure 2 appears.
POE-161 and POE-162S, the IEEE 802.3at Injector
Splitter Installation
1. Connect the AC adapter to “DC 56V” of POE-161. The
power LED will be steady on.
2. Connect a standard network cable from “Ethernet+DC”
port of POE-161 to “PoE In” port of POE-162S. The POE
In-use LED of POE-161 / POE-162S will light on continu-
ance.
3. Connect a standard network cable from Switch/worksta-
tion to “Ethernet” port of POE-161.
4. Connect the UTP cable in the package from “Ethernet”
port of POE-162S to the RJ-45 port of remote device.
5. Adjust proper DC power output and connect DC plug
from “DC OUT” of POE-162S to remote device.
6. Power on the remote device and its power LED indicator
will remains on.
Switch
100 meters
PoE
Power Data
PTZ Speed
Dome
POE-161
Power
Data
AC
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Power Line (AC) AC
Figure 2: Connection to IEEE 802.3at device
Once POE-161 detects the existence of an IEEE 802.3at
device, the POE In-use LED indicator will be steady on to
shows it is providing power.
Note
1. Since the POE-161 PoE port supports 56V
DC PoE power output, please check and
assure the Powered Device (PD) acceptable
DC power range is from 52 to 56V DC.
Otherwise, it will damage the Powered
Device (PD).
2. If the connected device is not fully complying
with IEEE 802.3at Power over Ethernet or in-
line power device, the LED indicator of POE-
161 will not be steady on.
Switch
POE-162S
POE-161
100 meters
Power
Data
Power
Data
PoE
Power Data
DC DC
PTZ Camera
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Power Line (DC) DC
Power 12V/24V
Figure 3: Connection architecture over POE-161/POE-162S
Note
1. According to IEEE 802.3at Power over
Ethernet, the POE-161 will not inject power
to the cable if not connecting to IEEE
802.3at devices.
2. Please ensure the output voltage is correct
before applying power to remote device.
Customer Support
Thank you for purchase PLANET products. You can browse
our online FAQ resource at the PLANET Web site first to
check if it could solve you issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
[email protected]
Copyright © PLANET Technology Corp. 2011.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology
Corp. All other trademarks belong to their respective
owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product : IEEE 802.3at High Power over Ethernet Injector (25 Watts)
*Model Number : POE-161
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (CLASS A: 2006 + A1:2007)
EN 61000-3-2 (2006)
EN 61000-3-3 (1995+A1:2001+A2:2005)
EN 55024 (1998+A1:2001+A2:2003) EN 50130-4 (1995+A1:1998+A2:2003)
IEC 61000-4-2 (2008) EN 61000-4-2 (1995)
IEC 61000-4-3 (2008) EN 61000-4-3 (1996)
IEC 61000-4-4 (2004) EN 61000-4-4 (1995)
IEC 61000-4-5 (2005) EN 61000-4-5 (1995)
IEC 61000-4-6 (2008) EN 61000-4-6 (1996)
IEC 61000-4-8 (2009) EN 61000-4-11 (1994)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:

Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title : Product Manager
Taiwan 27, Aug., 2010
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528