PLANET POE-165S - Manual (Page 2)

- 9 -
- 10 -
- 11 -
6. Hardware Installation
The following section describes the hardware features
of POE-165S. Before connecting any network device to
them, please read this chapter carefully.
Note
1. Please ensure the output voltage is correct
for remote device. Otherwise, it will damage
your remote device.
2. Forbid to switch the Power DIP during
operation. Otherwise, it will damage your
POE-165S and remote device. If want
to switch the output Voltage DIP, please
Plug-OFF the “POE In” cable and wait for
5 seconds until the POE LED (Power) is
completely OFF.
3. Please check and assure your Powered
Device (PD) power is through pin 4/5 (+)
& 7/8 (-). Otherwise, it will damage the
Powered Device (PD).
6.1 The POE-165S Installation
1. Select the correct output voltage by DIP Switch to
fit the remote device.
Passive
PoE Out This is non-802.3af/at injector
Incorrect voltage might cause device damage CAUTION
12V 19V 24V
Disconnect “PoE In” cable
before changing Voltage
Note
Pin 4, 5( +); Pin 7, 8(-)
2. Connect standard UTP cable from “Passive PoE
Out” port of POE-165S to remote device.
Note
Please use Straight cable for Passive PoE Out
port only.
3. Connect standard UTP cable from “802.3af/at PoE
In” port of POE-165S to PoE switch/injector.
Outdoor
Wireless AP
Power
12V/19V/24V
PoE 100Base-TX UTP with PoE
802.3af/at In-line
Power Switch/Injector
PoE PoE
Standard PoE Power Data Passive PoE Power
Data
POE-165S
90 meters 10 meters
7. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on the PLANET Web site
first to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
[email protected]
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
For the following equipment:
*Type of Product : IEEE 802.3af/at to Passive PoE Power Converter (12V/19V/24V)
*Model Number : POE-165S
* Produced by:
Manufacturer‘s Name : PLANET Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
Is here with confirmed to comply with the requirements set out in the Council Directive
on the Approximation of the Laws of the Member States relating to Electromagnetic
Compatibility (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (Class A : 2006+A1:2007+A2:2010+AC:2011)
EN 55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2007+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:

Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title : Product Manager
Taiwan 15, July, 2013
Place Date Legal Signature