PLANET POE-173 - Manual (Page 2)

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
Note
If the connected device is not fully
complying with IEEE 802.3at / 802.3af
Power over Ethernet or in-line power
device, the LED indicator of Ultra PoE
Injector will not be on steadily.
The Ultra PoE Injector and Splitter Installation
Below are steps showing how to install the PLANET
Ultra PoE Injector (POE-173) and Ultra PoE Splitter
(POE-171S) in pair.
Switch
Power 12V/19V/24V POE-171S
100 meters
Power
Data
Power
Data
PoE
Power Data
AC DC
Laptop
1000BASE-T UTP
PoE 1000BASE-T UTP with PoE
Power Line (AC) AC
DC Power Line (DC)
POE-173
Ultra PoE
Splitter Ultra PoE Injector
Figure 3: Topology of the Connection of POE-173 and
POE-171S
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on
steadily.
2. Connect a standard network cable from “POE”
port of Ultra PoE Injector to “PoE In” port of
POE-171S. The “ACTIVE” LED of Ultra PoE
Injector and POE In-use LED of POE-171S will
light up continuously.
3. Connect a standard network cable from Switch /
workstation to “LAN” port of Ultra PoE Injector.
4. Connect the UTP cable in the package from
“Ethernet” port of POE-171S to the RJ45 port of
remote device.
5. Adjust proper DC power output and connect DC
plug from “DC OUT” of POE-171S to remote
device.
6. Power on the remote device and its power LED
indicator will remain on.
Note
Please make sure the POE-171S output
voltage is correct before applying
power to remote device. The POE-171S
provides DC12V/19V/24V power output.
The Ultra PoE Injector and PoE Extender
Installation
Below are steps showing how to install the PLANET
Ultra PoE Injector (POE-173) and 802.3at PoE+
Extender (POE-E201) to extend the distance of
networking.
802.3at
PoE Extender
Data
PoE PoE
+ Power
Power
Data + Power Data
100 meters 100 meters
200 meters
Power Line (AC) AC 1000BASE-T UTP
PoE 1000BASE-T UTP with PoE
PoE IP Camera POE-173
Figure 4: Topology of the Connection of POE-173 and
POE-E201
1. Connect the AC power cord to “AC slot” of
Ultra PoE Injector; the “POWER” LED will be on
steadily.
2. Connect a standard network cable from “POE”
port of Ultra PoE Injector to the “IN” port of
POE-E201.
3. The Ultra PoE Injector delivers both Ethernet Data
and PoE power over UTP cable to the POE-E201
and the “ACTIVE” LED of Ultra PoE Injector and
“PoE IN” LED of POE-E201 will light up continu-
ously.
4. Connect the additional standard network cable
to the remote Powered Device (PD) via the
“OUT” port of POE-E201.
5. The “OUT” port is also the power injectors which
transmits DC voltage to the standard network
cable and transfer data and power simultaneously
between the Ultra PoE Injector and PD.
6. Once POE-E201 detects the existence of an IEEE
802.3at / 802.3af device, the “PoE OUT” LED
indicator will be on steadily to show it is providing
power.
Note
1. If the connected device is not fully
complying with IEEE 802.3at /
802.3af standard or in-line power
device, the PoE OUT LED indicator of
POE-E201 will not be on steadily.
2. According to IEEE 802.3at / 802.3af
standard, the POE-E201 will not inject
power to the cable if not connected
to a standard IEEE 802.3at / 802.3af
device.
Customer Support
Thank you for purchasing PLANET products. You
can browse our online FAQ resource at the PLANET
Web site first to check if it could solve your issue. If
you need more support information, please contact
PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
[email protected]
Copyright © PLANET Technology Corp. 2015
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product : Single-Port 10/100/1000Mbps Ultra PoE Injector (60 Watts)
*Model Number : POE-173
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022 (2006 + A1:2007 + A2:2010)
EN 61000-3-2 (2006 + A1:2009 + A2:2009)
EN 61000-3-3 (2008)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1: 2007 + A2:2010)
IEC 61000-4-4 (2004 + A1:2010)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title : Product Manager
Taiwan 24 th May, 2013
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528