PLANET POE-E201 - Manual (Page 2)

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Note
1. To provide you better PoE power and data
extension quality, we strongly recommend that
you use “Solid UTP Cable” when installing
POE-E201.
2. The POE-E201 can be installed with third-party
device if the device complied with IEEE 802.3at
/ 802.3af standard.
3.2 Connect POE-E201 to the Power Source
Equipment (PSE)
There are 2 RJ-45 ports in the PoE Extender, of which
the “IN” port functions as "PoE (Data and Power)
input" and the “OUT” port on the other side functions
as "PoE (Data and Power) output".
Step 1: Connect a standard Cat.5/5e/6 UTP cable from
Power Source Equipment (PSE), such as
PoE Switch, PoE Injector hub and single port
PoE injector, to the “IN” port of POE-E201.
Step 2: The PSE delivers both Ethernet Data and PoE
power over UTP cable to the POE-E201 and the
“PoE IN” LED will be steady on.
Note
1. The POE IN LED turn on steady green means
POE-E201 is being powered successfully with
PoE class 0.
2. If POE IN LED does not turn on, please check
the remote PSE or the cable with a PC or a
network device to see if the cable is correct. Or
with an IEEE 802.3at / 802.3af device such as
the target PD to check the power injection is
correct either.
3.4 Multiple PoE Extender Installation
The POE-E201 PoE Extender supports multiple units,
daisy-chain installation. They can be employed in
series for even longer distances based on remote
PoE IP Camera or PoE Wireless Access Point power
requirement.
Step 1: Connect the additional Cat.5/5e/6 cable from
the “OUT” port of the first POE-E201, the
other end of the UTP cable be used to connect
to the “IN” port of remote / next POE-E201.
Step 2: The “PoE OUT” LED indicator of the first
POE-E201 will be steady to shows it is
providing power to next PoE Extender.
Step 3: The “PoE IN” LED on the next POE-E201 will
steady on.
3.3 Connect POE-E201 to the Powered
Device (PD)
Step 3: Connect the additional Cat.5/5e/6 cable
that will be used to connect to the remote
Powered Device (PD) to the “OUT” port of
POE-E201.
Step 4: The "OUT" port is also the power injectors
which transmit DC Voltage to the Cat.5/5e/6
cable
and transfer data and power
simultaneously between the PSE and PD.
Step 5: Once POE-E201 detects the existence of an
IEEE 802.3at / 802.3af device, the “PoE OUT”
LED indicator will be steady, ON to shows it is
providing power.
PoE IP Camera
POE-E201
802.3at
PoE Extender 802.3at
PoE Injector
PoE PoE
AC
+ Power Data
Data
+ Power Data
Power
100M 100M
200M
DC
Power Line (AC) AC
DC Power Line (DC)
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Note
1. If the connected device is not fully complying
with IEEE 802.3at / 802.3af standard or in-line
power device, the PoE OUT LED indicator of
POE-E201 will not be steady on.
2. According to IEEE 802.3at / 802.3af standard,
the POE-E201 will not inject power to the cable
if not connecting to a standard IEEE 802.3at /
802.3af device.
Step 4: Connect the additional Cat.5/5e/6 cable to the
remote PoE powered device to the “OUT” port
of next or third POE-E201.
POE-E201
802.3at PoE Ethernet
Switch/Injector Hub
UPS
PoE
100M
PoE
100M
Outdoor IR IP Camera
non-PoE IP Camera
802.3at
PoE Splitter
PoE
PoE
PoE
100M
100M
100M
PoE
PoE
PoE
100M
100M
100M
DC
Power Output
300m 200m 100m 0m Distance
AC
AC
(20W)
400m
(16W)
500m
(12W) (24W) (30W)
POE-E201
802.3at PoE Extender
802.3at PoE Extender
802.3at PoE Extender
802.3at PoE Extender 802.3at PoE Extender 802.3at PoE Extender
POE-E201
802.3at PoE Extender
POE-E201
PoE
100M POE-E201
PoE
100M POE-E201
PoE IP Camera
POE-E201
Power Line (AC) AC
DC Power Line (DC)
1000Base-T UTP
PoE 1000Base-T UTP with PoE
Note
1. Per POE-E201 will take 3.2 Watts maximum for
the system itself, please check the total power
consumption of your IEEE 802.3at / 802.3af
PD and the POE-E201 before you make the
daisy-chain connection. If the overall power
consumption is overloaded, the local PSE could
shutdown the whole power system.
2. Per POE-E201 cable segment is limited in 100
meters Cat.5/5e/6 UTP wire from its IN/OUT
port to the other data end, use of any other
non standard cable or over distance could re-
sults in unstable connection.
3.5 Optional - DIN-Rail Mounting
There are two DIN-Rail holes on the left side of the
POE-E201 that allows the Extender can be easily
installed with DIN-Rail mounting. The PLANET optional
DIN-Rail mounting Kit – RKE-DIN can be order
separately. When need to replace the wall mount
application with DIN-Rail application on the POE-E201,
please refer to following figures to screw the DIN-Rail on
the Extender. To hang the POE-E201, follow the below
steps:
Step 1: screw the DIN-Rail on the POE-E201.
Step 2: Lightly press the button of DIN-Rail into the
track.
1
2
Step 3: Check the DIN-Rail is tightly on the track
You must use the screws supplied with the
mounting brackets. Damage caused to the parts
by using incorrect screws would invalidate your
warranty.